Hello,
I want to model a parabolic hole in a slab using ABAQUS. Can i do it? if Yes how?
Hi Prashant
yes, it is possible.
1) in the part module select the slab,
2) in the left ribbon options, select the "cut extrude"
3) you will be gone back to the sketch part
4) draw your section
5) Done.
Best Lucks
hello sir,
thank you for the reply, i understand what you said, but even then i think you cannot create a circular parabolic duct at the center of slab.
Can you please draw a sketch? I am not able to get what exactly are you looking for.
SURE SIR
In the part module
1. Shape menu (at the top) > Cut > Sweep.
2. In the appeared menu,
(i) Sketch the path, i.e. parabola along the slab
(ii) Sketch profile, i.e. circle on the face normal to the path
You will be get it.
Exactly.
Plz follow the Mr. Faye instruction to approach your goal.
Dear Mr Faye and Mr Ghaedi.
Thank you for taking out time and replying
Yes its working this way but sir again how do i define the sweep at the center of slab. it is only possible to sweep cut on the faces this way.
Sweep path is independent of the sweeping geometry. You sketch the sweep path at the face and sweeping circle at the center of the slab. That should not be a problem.
I am looking for any completed/ ongoing project in India where either Basalt FRP rebar or Basalt Fibres have been used
05 June 2018 9,265 0 View
Hi I am trying to model FRP strands inside Prestressed Concrete. i wrote a UMAT code for defining Constitutive law for FRP. The linear analysis runs fine, however, after defining CDP I am...
09 October 2017 1,829 3 View
Hi, I am trying to model FRP strands (3D Continuum ) in ABAQUS. Since ABAQUS does not allow Hashin damage model to be utilized in 3D elements, I am planning to write a UMAT code for it. My doubt...
09 October 2017 2,160 0 View
Hello, I recently wrote a UMAT code for FRP bars transversely Isotropic). But, while starting the job I get "Compilation Error". Can someone take a look at the code and suggest what is wrong in...
09 October 2017 5,669 0 View
I am trying to link ABAQUS 6.13 with intel parallel studio 2013 and visual studio 2010. On opening abaqus i get following notifications. (please see attached image ) Whereas while running the...
09 October 2017 6,784 2 View
I am simulating prestress operation in ABAQUS. During this stage the prestress member is allowed to develop upward camber but at the same time, it is constrained in the downward direction. Such...
08 September 2017 9,552 0 View
I am modelling Pretensioned Bridge Girder. Initial prestress has been defined in the model and the strands transfers the stress to concrete. I need to calculate manually the stresses that is...
07 August 2017 8,787 2 View
Hello, i modelled a Pretensioned beam with tendons as solid elements. the model ran fine. Now i am planning to model the pretension beam with wire element instead of solid element, in place of...
31 December 2016 2,545 10 View
I have attached the experimental protocol for the test. My questions is 1) should I give this as it is in the tabular column while defining amplitude 2) what should i give the time period value in...
02 March 2015 1,863 4 View
I am intending to calculate the energy dissipation during the 1st cycle of loading. i have attached the excel sheet which gives details for the 1st cyle of loading. i will be grateful if anyone...
01 February 2015 1,539 6 View
I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.
11 August 2024 9,101 4 View
I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?
11 August 2024 5,138 1 View
Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!
11 August 2024 3,770 4 View
Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...
10 August 2024 7,180 0 View
I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...
10 August 2024 7,429 2 View
How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?
09 August 2024 7,718 0 View
I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...
08 August 2024 4,831 4 View
Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...
07 August 2024 1,937 1 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
A fungal strain was treated with nanoparticles. We want to do an environmental SEM analysis. So could anyone share your views on preparing the sample? Thank you.
07 August 2024 5,307 1 View