Hello,
I recently wrote a UMAT code for FRP bars transversely Isotropic). But, while starting the job I get "Compilation Error".
Can someone take a look at the code and suggest what is wrong in the code?
I am looking for any completed/ ongoing project in India where either Basalt FRP rebar or Basalt Fibres have been used
05 June 2018 9,265 0 View
Hi I am trying to model FRP strands inside Prestressed Concrete. i wrote a UMAT code for defining Constitutive law for FRP. The linear analysis runs fine, however, after defining CDP I am...
09 October 2017 1,829 3 View
Hi, I am trying to model FRP strands (3D Continuum ) in ABAQUS. Since ABAQUS does not allow Hashin damage model to be utilized in 3D elements, I am planning to write a UMAT code for it. My doubt...
09 October 2017 2,160 0 View
I am trying to link ABAQUS 6.13 with intel parallel studio 2013 and visual studio 2010. On opening abaqus i get following notifications. (please see attached image ) Whereas while running the...
09 October 2017 6,784 2 View
I am simulating prestress operation in ABAQUS. During this stage the prestress member is allowed to develop upward camber but at the same time, it is constrained in the downward direction. Such...
08 September 2017 9,552 0 View
I am modelling Pretensioned Bridge Girder. Initial prestress has been defined in the model and the strands transfers the stress to concrete. I need to calculate manually the stresses that is...
07 August 2017 8,787 2 View
Hello, i modelled a Pretensioned beam with tendons as solid elements. the model ran fine. Now i am planning to model the pretension beam with wire element instead of solid element, in place of...
31 December 2016 2,545 10 View
I have attached the experimental protocol for the test. My questions is 1) should I give this as it is in the tabular column while defining amplitude 2) what should i give the time period value in...
02 March 2015 1,863 4 View
I am intending to calculate the energy dissipation during the 1st cycle of loading. i have attached the excel sheet which gives details for the 1st cyle of loading. i will be grateful if anyone...
01 February 2015 1,539 6 View
I have modelled I Section with tendon as 3D solid. I have applied prestress in Initial step under predefined field and then applied pseudo static load to match the load deflection curve with...
01 January 1970 539 4 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
Request Python code from this article : Gender equity of authorship in pulmonary medicine over the past decade. THANKS!
08 August 2024 6,242 2 View
Visual Studio Code (VS Code) has become a popular choice among developers for several reasons: 1. **Free and Open Source**: VS Code is free to use and open source, making it accessible to...
07 August 2024 7,013 4 View
I need the python code to forecast what crop production will be in the next decade considering climate and crop production variables as seen in the attached.csv file.
05 August 2024 2,977 3 View
Details of the Analysis. Static Analysis Composite Layup Continuum Shell Elements FRP Material (Elastic and Hashin Damage)
03 August 2024 8,538 4 View
all math can be traversed by code? all math can be translate to code?
26 July 2024 9,530 0 View
Currently, I have created a gate-all-around process using sentaurus tcad and I am trying to measure the noise using the cmos noise code. However, an error occurred during the simulation. The error...
24 July 2024 6,352 0 View
Dear all, I have a user written estimation code based on the paper dynamic panel data estimations with fixed effect by Galvao(2009). I have seen many papers using this method and pvalue, standard...
22 July 2024 4,588 1 View
Where do I download the codes, databases commonly used by researchers?
16 July 2024 295 0 View
Hello, dear RG community. Personally, I have found Xarray to be excruciatingly slow, especially for big datasets and nonstandard operations (like a custom filtering function). The only suggestion...
15 July 2024 4,705 2 View