I would like to introduce non-spherical particle like cylinder, rod, cone etc. is it possible to introduce the shape by using shape factor. If it is possible to define particles shape by using FLUENT, could you please explain.
I am interested to your question (similar to my case).and will explain in detail soon. Bit hurry for this time, please consult me.
I know you can select non-spherical drag force in Fluent
Definitely, it is not possible, but you can incluide the non spherical effect in the drag model through UDF .
Instead of checking only the mRNA level, I want to check the active protein level of MMP-1 in Liver tissue from mice. How can I do that?
03 March 2021 1,763 2 View
I want to analyses the proportion of swimming sperm of three species of fish in two salinities. To analyse the proportion of swimming sperm in a Generalized Linear Model, I would use a Binary...
03 March 2021 2,297 3 View
03 March 2021 8,272 1 View
Hi. Please tell me what guidelines should i need to follow for questionaries' type research work in India. It is not hospital based work, we are conduction basic institutional based qualitative...
03 March 2021 2,037 3 View
Hi, I implemented a code to gabor filter cifar10 data but the images after being filtered and stacked are not clear like the original images. I think the problem is in the way I am using the...
03 March 2021 6,317 1 View
i am try to classify the x-ray images. During classification , can i block unwanted images (except x-ray image).
03 March 2021 7,100 1 View
03 March 2021 5,360 2 View
The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...
03 March 2021 4,107 4 View
If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis
02 March 2021 7,670 3 View
02 March 2021 5,204 3 View
Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,
02 March 2021 0 0 View
Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...
02 March 2021 4,910 3 View
Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...
01 March 2021 9,911 3 View
I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...
01 March 2021 6,661 3 View
I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...
01 March 2021 8,668 3 View
I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...
01 March 2021 736 3 View
Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?
01 March 2021 9,785 3 View
I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...
01 March 2021 8,415 1 View
How can one improve mesh skewness, orthogonality, aspect ratio?
28 February 2021 7,730 3 View
I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...
28 February 2021 4,841 3 View