Which programs are to be used to register 2D image onto a 3D image data set?

I am trying to register a light micrograph onto a 3D CT data set, as I want to extract the corresponding image from the CT data set. Is there any software or program can do this accurately? I am...

21 February 2021 8,220 3 View

Are there any Statistical Quality Controlling researches based on the survey?

I want to know about uses of Statistical Quality Controlling techniques in the industries. And I hope to study this matters on survey with questionnaire.

26 December 2020 3,284 3 View

ANN does not process information.It only represent information. ?

Are there any research improvements related to attention, emotions, motivation, pleasure, consciousness and personality developed using ANN.

21 August 2018 8,983 4 View

How to model the soil pile interaction using spring elements in ANSYS workbench? Is it possible to introduce multiple springs?

In mechanical APDL, combin39,14 elements can be used. But how to use multiple spring elements in ANSYS workbench.

23 October 2017 637 2 View

Nuclear fractionation? I want see Cyclin B1 levels in cells arrested in G2/M phase. Does nuclear fractionation is required for this?

18 March 2017 337 5 View

What are the rainfall-runoff method specify to small,steep catchment area??

i want to know about rainfall-runoff method that can be convert rainfall to runoff discharge specify for small,steep catchment area.

05 February 2017 7,247 19 View

Is there anybody who has used caffe deep learning framework for image classification in a Raspberry Pi?

06 March 2016 8,898 9 View

Is there anyone who has experience with design software for drawing their own Software Diagrams ?

Diagram output goes to Simple Software. Main GoalDevelop an Accountable Software like billing System or Stock Management through Identify Graphical Diagram that can easily learnable by...

08 March 2015 3,426 14 View

Do any of you use following combination for EEG acquisition?

24 February 2015 8,409 3 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Complex wave form in ANSYS?

Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...

27 February 2021 5,969 1 View

What is the best way to calculate the angles of twist for concrete columns subjected to torsional moment using finite element software?

In Finite element software like ANSYS , there is difficulty in obtaining direct results of twisting of concrete members because SOLID65 which is the unique element designed to represent concrete...

26 February 2021 3,806 2 View