Is anyone working with GEM software for simulation of saline aquifers?

More Ankita Mukherjee's questions See All

Which type of compound does lamda max of 218 indicate in a uv-vis spectrum of a partially purified compound through column and TLC?

A crude extract of fungal culture using EtOH was subjected to column and TLC and partially purified compound was obtained. UV vis spectrum of the compound/s has max absorbance at 218nm. The...

11 August 2024 9,801 2 View

Conjugation of PEG-Amine to an Amino Acid Using EDC?

I am attempting to conjugate PEG to an amino acid at the C-terminus, for the purposes of producing nanoparticles. I have been told that PEG modified with amine groups can be used for this purpose,...

31 July 2024 2,033 1 View

Does soybean seed coat or cotyledon contain chlorophyl or flavonoids? What types? determined by paper chromatography? other methods (high school lab)?

Am trying to develop a lesson/lab to determine and compare antioxidant properties of soybeans of various colors. Preference would be low tech and low cost. Any assistance is greatly appreciated.

25 July 2024 7,498 2 View

Does post-translational protein modification cause devisions on observed pI verses calculated pI?

In running two-dimensional gel electrophoresis on bacterial protein, some spots that appear to match a protein sequence have a significantly more acidic isoelectric point than the calculated pI....

24 July 2024 8,076 3 View

How I can add anew research in my account ?

Their is new research published in the biological control journal, and I am one of the authors. I want to add it to my account at researchgare. How can I do this?

21 July 2024 7,545 0 View

Can Document Analysis be used as the only method of research?

I have read that it is better to use other research methods alongside document analysis for triangulation, although it can also be used as a stand-alone method.

18 July 2024 4,218 0 View

How much sample we are required to do a pilot study for standardized an Achievement Test?

I am conducting a study on Effectiveness of e-content on academic achievement of secondary school science student.

17 July 2024 5,633 4 View

Masonry Interaction Module ABAQUS?

I am simulating interlocking / dry stacked masonry in Abaqus. I am using a friction coefficient of 0.6 for my model as it is stated in the previous research as well as in the base paper. The...

16 July 2024 5,047 0 View

What is wrong with my input file?

im studing gaussian 16 with reading paper about I-131 Metaiodobenzylguanidine in the paper "In a similar vein, nuclear magnetic resonance shielding values were investigated using the widely...

16 July 2024 6,040 4 View

Can ROBINS-I be used to measure risk of bias in single-arm studies?

I am doing a systematic review, and I am measuring risk of bias with RoB2 for RCT, and ROBINS-I for non RCT. My questions is, for single arm studies, can I use ROBINS-I? I am not sure how to...

14 July 2024 3,570 5 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to prepare the nanoparticle treated fungal sample for Environmental SEM analysis?

A fungal strain was treated with nanoparticles. We want to do an environmental SEM analysis. So could anyone share your views on preparing the sample? Thank you.

07 August 2024 5,307 1 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View