In simulation of the Quasi-static indentation of sandwich composite structure, how do I get the values of Hashin damage , damage evolution and damage stabilization.
Dear Azzam
Do you check these outputs in the step module ?
Best regards
Stephane
Someone explain to me some methods to get the Force-displacement curve from Abaqus for whole model .
31 December 2014 7,612 10 View
I am trying to install Abaqus 14.1 in windows 8.1 but I didn't complete it well, please someone tell how I can install it.
31 December 2014 4,579 1 View
Which suitable type of interaction should be used between composite top face sheet, foam and lower face sheet in Abaqus and how we can make it? How do I model the skins as S8R elements and the...
09 October 2014 4,401 4 View
It could be not abaqus
08 September 2014 6,165 5 View
In TexGen I like to transfer IGES file , surface Mesh, volume Mesh , STEP file , ABAQUS file and Tetgen Mesh so which file suitable with abaqus
08 September 2014 2,969 2 View
How to simulate twill weave fabric structure by Abaqus software program
08 September 2014 8,651 0 View
If you fabricate composite laminate consist of 8 ply [0,90,45,-45]s how we can detect the damage which occurred in laminate after impact test? I know C-scan method (NDT), but only detect the...
08 September 2014 3,577 5 View
The stacking sequence of the fabric structure could be , for example [0/90, ±45, 0/90] this structure has three layers , how can design it in composite lay-up in abaqus program software ,
08 September 2014 1,224 2 View
Please give some examples using ANSYS, ABAQUS and COMSOL MULTIPHYSICS
01 January 1970 7,131 1 View
I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.
11 August 2024 9,101 4 View
I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?
11 August 2024 5,138 1 View
Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!
11 August 2024 3,770 4 View
Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...
10 August 2024 7,180 0 View
I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...
10 August 2024 7,429 2 View
Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...
10 August 2024 6,493 1 View
How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?
09 August 2024 7,718 0 View
I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...
08 August 2024 4,831 4 View
Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...
07 August 2024 1,937 1 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View