How the geospatial variability in the heat requirements of crop due to rising temperatures analyzed?

As we know that the global temperatures are increasing due to climate change which could affect the thermal needs of the crops. I want to make geospatial maps and analysis for heat requirements of...

28 September 2020 8,286 2 View

Can any body suggest the funding agency for Research Project on climate change and Remote Sensing?

I tried to submit research projects on climate change and Remote sensing to many agencies but could not get it though? Is there any easily available agencies who support the research in the subject.

16 August 2020 4,000 18 View

How to determine the primary productivity of a grassland ecosystem?

I am looking for a reliable method to determine the productivity in grassland and forest communities.

15 January 2020 6,592 3 View

Fill Factor showing infinity.Why?

I measured IV characteristics on thin film semiconductor using a solar simulator and the fill factor showed infinity. Any reason why am seeing this?

09 December 2019 2,731 4 View

Rice is grown over the large area across the country during the summer season. Is there any impact of such practice on the hydrological cycle ?

Standing water over a larger area for a prolonged perio during the high water requiring crop may change the hydrological dimensions and also rainfall patterns at regional level. ...

25 March 2019 2,067 6 View

How to write and insert the UDF in ANSYSY Fluent ?

Specifically: Monod-type reaction for biomass growth calculations

25 February 2018 7,950 3 View

How to write and insert boundary conditions as UDF in ANSYSY Fluent ?

For a rectangular 2D geometry

25 February 2018 3,725 3 View

Is anybody using ANSYS Fluent for the Development of Bioreactor for the study of its computational fluid dynamics in India ?

For the designing modeling and the simulation pupose

19 February 2018 2,226 3 View

How can I simulate the algal growth model in the bioreactor via using ANSYS FLUENT ?

For the study of light and bubble formation inside the PhotoBioreactor.

19 February 2018 8,424 5 View

Which one is the best software for molecular dynamic simulation?

for protiens

04 December 2016 5,958 32 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View