Is anybody interested in numercal simulations?

More Saravanan Manickam's questions See All

What could be the possible reason for the drastic variation in Qmax value for same adsorbent onto two different cationic dyes itself?

The adsorption capacity of the rice husk biochar was varying drastically with two cationic dyes namely Basic Blue 41 and Basic Red 09? What could be the possible reason behind this?

30 January 2021 1,420 3 View

Formula to determine the length of piping required for heated N2 gas?

Heated Nitrogen gas will be allowed to flow through stainless steel piping as part of my project.Hence, I need help to generate a formula in excel to calculate the length of piping required for...

17 August 2020 2,031 5 View

Which software is best to plot paleoclimate data with high resolution?

Dear All, I'd like to plot high-resolution figures of paleoclimate data, Please suggest the best and most friendly software. Advance thanks, Saravanan

25 July 2020 3,003 6 View

What are the high yielding methods of extraction of phycocyanin from dry mass of Anthirospira plantesis?

extraction techniques

31 January 2020 7,268 1 View

Why ellipsometer spectrum of silicon nitride (SixNx) shows the number of peaks at 530 nm excitation wavelength?

We have deposited the silicon nitride (SixNx) on the silicon (Si) substrate using atmospheric pressure chemical vapor deposition (APCVD) technique. After the measurements, the ellipsometer results...

03 January 2020 1,400 3 View

Is there any upadate in List of Journals in JCR 2019?

Journal indexed in web of science JCR 2018 is attached . Can any one tell me any updates in JCR report 2019

27 April 2019 7,306 3 View

Why XRD pattern of ZnO nanorods prepared on FTO glass by electrochemical deposition is different than the others?

We have attempted to prepare nanorods on FTO plate by electrochemical deposition. In general XRD pattern of ZnO yields 2 theta 31, 34, 37 corresponding to (100), (101) and (002) planes. In our...

18 March 2019 7,633 4 View

How to do multi-step analysis in Abaqus?

I am doing bolt load and torque load sequentially. But not sure that my result going to valid.

28 January 2019 8,965 3 View

How much powerful BLDC motor do I need for my 200 kg motor bike?

Hi, I have a motorbike weighing 200 Kg, running with IC engine, Now I intend to convert it electric using BLDC, I aim top speed of 80 kmph, and no problem with acceleration it can as low as...

19 September 2018 8,718 7 View

How good the antibodies from Sabbiotech, USA?

Hello, Had anyone used antibodies from Signalway, Sabbiotech, USA for western blotting?. If so, kindly gives your comments about the quality of primary antibodies.

29 July 2018 2,042 1 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Do anyone here can help us in the field of molecular docking?

We have synthesized various metal complexes with different environment around the metals. Now to see the application of synthesized complexes we need this study also. we are also interested in...

01 March 2021 1,899 2 View

In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein?

Hi In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein? I got this error in the add-ion stage: Fatal error "./ amber99sb-ildn-HHH.ff / force...

01 March 2021 8,747 4 View

Maxim V. Shamolin

yes

Dmitry Skiba

It may be interesting

Jitendra Singh Pal

yes it is useful for the new problem solving like multiple phase analysis of engine exhaust.

Henokh Lugo Hariyanto

Could I know the nonlinear evolution equation that want to be solved by numerical simulation?

Ahmed Bouzidane

I, too, am very interested in this position.