Influence of sulfur and phosphorus in the toughness of quenched and tempered steel?

12 December 2017 0 3K Report

Hi People. In my case I work with a high carbon steel (0,82%C).

I need to know which is the Influence of sulfur and phosphorus in the toughness of quenched and tempered steel?

Badges
Science topic

More Daniel Martinez Krahmer's questions See All

Sheet steel laser cutting?

If you have a laser cutting machine that can cut a steel sheet up to 10 mm thick, is it possible to cut a 20 mm steel sheet in two consecutive passes? If the answer is yes or no, why?

09 October 2019 9,436 3 View

Lubrication regimen in pin on disk test?

I know that a way to establish the lubrication regime in a pin on disk test is by measure the resistance between the pin and the disc. Some papers say that if the resistance is of 2 ohm, the...

05 June 2019 7,949 3 View

How to create a mechanical engineering graphical abstract ?

Hi People. Here in RG there is a similar question but for works in biology. Some of you know if is there any software available to design mechanical engineering graphical abstracts ? Something...

31 December 2018 3,587 2 View

Warm forging of SAE 1045 steel?

Hi People. I need to know the temperture range for making warm forging of SAE 1045 steel.

31 December 2018 4,719 0 View

Hot forging dies made by SAE H13 tool steel?

Please. I need to know what level of hardness provide a equilibrated behaviour between wear resistance and toughness. Also, if a ionic nitriding treatment reduce the friction factor between the...

10 November 2018 6,622 1 View

Redes neuronales artificiales?

Esta pregunta es solo para los amigos y amigas de RG que hablan español. Les quiero preguntar si me pueden recomendar, al juicio de cada uno, cual es el mejor libro en ESPAÑOL para poder aprender...

09 October 2018 8,917 0 View

Turning of low carbon steel?

People. I need your colaboration. What value of hardness do you think is the minimal to not worsen the maquinability level of the steel? I work with steel of 0,1% C. I some of you have a paper, is...

08 September 2018 9,430 3 View

How do I assess ignition risk during magnesium turning?

Some people say that the risk is bigger when the chip particles size are 500 micrometers or minus? What is the reason of this size?

07 August 2018 7,725 0 View

Recrystallization temperature of one steel?

Please. I need information about the recrystallization temperature of SAE 1010 steel, and also the temperature range for warm forging.

05 June 2018 5,844 3 View

Grinding ball manufacturing by hot rolling process?

Hi People. Please, I need to know which is the best material to make the guideline plate in a hot rolling grinding ball machine. Here the is a link to see the...

02 March 2018 832 6 View

What is the reason for current dropping in OER , LSV curve?

I tried four trials of the same Copper Phosphides sample in Alkaline medium ( 0.5M KOH) with Hg/HgO reference electrode and Pt as counter electrode. I used 0.001 V/s scan rate for first three...

10 August 2024 3,629 1 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

Do interactions between biosphere, carbon cycle, & water cycle impact global warming & interaction between atmosphere & hydrosphere?

How do interactions between the biosphere, the carbon cycle, and the water cycle impact global warming and interaction between the atmosphere and the hydrosphere?

09 August 2024 3,291 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Aspen Plus Simulation?

Greetings When one is to perform Simulation or modelling of Pyrolysis of Biomass Waste materials using Aspen Plus software, and one has both the macromolecules breakdown (Cellulose, Lignin and...

06 August 2024 5,023 1 View

Who of all of you will help TPEOM to re-originate the Earths atmosphere to it original 5 atmospheric elements/gases?

Global ‘Weather’ has stopped, as ‘aqua thermionic instituted by the ‘Global thermo atmospherics has instituted global thermodynamics of 120º C + and thus all waters are, or have boiled into a...

06 August 2024 8,716 0 View

How can I separate graphene from amorphous carbon of similar particle sizes?

The starting material is a finely ground powder. Some particles contain more graphene than others.

30 July 2024 3,978 2 View

Question about combustion Kinetics ?

I am currently working on modeling FCC catalyst regeneration and have come across a point of uncertainty that I hope you can assist me with. In my previous models, I have utilized lumped kinetics...

30 July 2024 6,137 0 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View