In CST Studio Suite, once a simulation is done, can we add farfield plots using field monitors without re-simulating the whole design?

More Aakash Bansal's questions See All

In PRIMER, is it possible to downweight certain taxa in multivariate community datasets to reflect uncertainty around identification??

I have a dataset with about 80 different species. As usual, some species are very easy to identify with certainty whereas others are more difficult, which means that I am less certain of my...

03 March 2021 8,066 4 View

How to get onecolumn document from standard IEEE ACCESS LateX template?

I have prepared a manuscript in IEEE Latex template, but for some purpose, I need to prepare a word file as well (detailed format is not required). Compared to two column .tex file, one column...

02 March 2021 1,830 3 View

Gel electrophoresis result for total RNA samples, 1.5 Agarose gel was used, How to improve the integrity of RNA?

Gel electrophoresis, RNA degradation, RNA extraction from fresh tissue

02 March 2021 5,433 5 View

How to grow E.coli on the low salt LB agar plate with 50 or 100ug/ml of Blasticidin?

Hello, I would like to ask how to grow E.coli which resists 50 or 100ug/ml of Blasticidin. I have tried many methods by using low salt Luria-Bertain(LB) agar plate. However, no colonies grow. Let...

01 March 2021 2,027 2 View

OpenBCI eeg--has anyone used them?

I'm looking to try out an off-the-shelf EEG set for some exploratory work. Curious if anyone has used the OpenBCI, and how much set-up work is required. I've heard they are more difficult to get...

01 March 2021 4,128 3 View

How to remove DCU and HOBT from my reaction?

I am doing a acid and a chiral amino alcohol reaction using DCC and HOBT in DCM or THF? Can anyone suggest me how to remove DCU and HOBT from a reaction mixture??

28 February 2021 2,153 1 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

B-mercaptoethanol (BME) protocol?

Hi everybody, I have been running a multiplex IHC which allow me to stain the same tissue with different markers (Primary Ab + Secondary conjugated Ab) (AF487, AF555, AF647). Since I would like to...

27 February 2021 5,028 2 View

What is the suitable range of Sulfur content and Viscosity of Heavy fluid Oil that used in Kiln?

What is the disadvantages of high sulfur content to the ceramic burning process? and what is the effect of outranged viscosity?

24 February 2021 8,219 2 View

Help request in CST microwave?

im working now on TPV solar cells and metamaterials and i realy need our help in CST microwave i have a tpv cell simulation and i want to extract particullarly the absorbtion of only the active...

02 March 2021 2,246 2 View

Does the circuit modeling for planar monopole antennas using Foster canonical forms give good approximation?

Hi researchers, I am searching for some accurate way to do the circuit modeling of planar CPW-fed monopole antennas. I have gone through the literature where mostly circuit modeling is done using...

28 February 2021 7,016 1 View

Compact antenna for the frequency range 1 MHz-5 MHz?

Hello everybody! I have a problem with developing a compact antenna for the 1MHz-5MHz frequency range. Tell me what type of antenna can be used and what books and articles to read to perform this...

27 February 2021 7,710 4 View

Can impedance of antenna be less than 50 ohms?

I am simulating helix antenna in hfss, right now, giving excitation with 50 ohms port. When I see the results of Z parameter (real). It shows lower than 50 ohms. Do not understand, if it can be...

27 February 2021 4,218 7 View

Is there a way to use waveguide ports for circular antenna design in CST?

Hi, whenever i use circular array i get this error "Waveguide ports must be aligned with Cartesian coordinate planes for the transient solver" Does anyone use circular array with waveguide ports?...

09 February 2021 3,609 8 View

How to model in HFSS or FEKO Free Space Material Characterization?

I am having trouble setting up this problem in HFSS or FEKO. In HFSS, I've tried both FEM and FEBI-IE solvers. With FEKO, I've tried it's MoM solver and default settings. I am would like model...

09 February 2021 375 2 View

What is best solution for optical metamaterial design calculation: HFSS, COMSOL, CST?

Dear all, Now I'm selecting FEM for design of metamaterials on NIR~VIS frequencies, and keeping 3 software: ANSYS HFSS, COMSOL with wave optics module, and CST STUDIO SUITE. Could you give me...

09 February 2021 9,517 2 View

Which journals (Q1,Q2) accept simulation based design and results of antenna if fabrication and testing facility is not available?

I need a list of good (preferably Q1,Q2) journals that will accept research papers prepared on designs done with the help of simulation software e.g CST, HFSS etc.

08 February 2021 9,636 5 View

How to achieve the sensitivity diagram of a sensor in CST?

I wanna design a sensor in CST 2021 for the first time and I don't know how to achieve the sensitivity diagram of the sensor in CST. Could you plz help me to do that? I appreciate your response...

26 January 2021 6,864 1 View

What is corrct way to define ports when simulating FSS and surface waves in CST?

I need to simulate a mushroom FSS and I'm struggling with the ports. What's the correct way to define them? Should I construct a proper SMA connectors, or is it enough to put a waveguide ports...

19 January 2021 6,590 4 View