What is the difference between a shared aperture antenna and a dual band antenna?

Can the dual-band antenna be called as a shared aperture antenna? Difference between shared aperture antennas and dual-band antennas?

30 December 2020 7,118 4 View

How to find x in LiFePO4 or LCO?

Dear Everyone, I am new to this battery field and want to know how to get x (amount of lithium (de)inserted) from the galvanostatic charge/discharge profile for any materials. I have attached...

26 December 2020 632 2 View

Does the adsorbed water or gases affect the CHNS analysis of high surface area porous carbon ?

Adsorbed water and gases can affect the weight of the porous carbon. Some times 6-7% weight loss can occur during the degassing of the sample. Will this weight loss affect the calculation of C,...

08 November 2020 5,399 3 View

Can I use low concentrate Sulfuric acid into drip irrigation?

Generally water alkalinity to clot the dripper nozzle due to salt formation. So bring down the irrigation water pH to 5.5 to 6.5 may useful for prevent for salt formation as well as crop...

31 August 2020 675 3 View

If a journal was scopus indexed at the time of article submission (2019); and not indexed at the time of article acceptance (2020)? How to proceed?

Hai, A journal which had indexed for scopus from 2018 to 2019. Article was submitted to journal in 2019. While the time of acceptance letter (March 2020), journal website had removed scopus from...

10 March 2020 3,875 6 View

What is the best procedure to isolate the Quercetin and Resveratrol from their sources?

BEST EXTRACTION AND ISOLATION PURIFICATION METHOD FOR QUERCETIN AND RESVERATROL FROM PLANT SOURCES? (i.e)Quercetin from Apple and Resveratrol from Blueberries? AND also does phenol exist in...

08 December 2019 9,884 5 View

Is any one know about yeast strain which use for stress tolerance experiment like INVSc1?

I work on some stress tolerance genes from plants. I clone those genes in pYES2 yeast expression vector and transform in to INVSc1 yeast strain to perform stress tolerance assay using different...

11 November 2019 2,248 1 View

For Structural Equation Modelling Analysis what type of Data's required in Maintenance ?

For Structural Equation Modelling Analysis what type of Data's required in Maintenance Engineering for Better P values and Composite Relaibility.

29 May 2019 4,992 2 View

Difference between point source, line source and plane wave excitation in FDTD?

Excitation in FDTD could be point source, line source and plane wave. What is the difference between the three? Also which type of source could be used for various applications like antenna,...

08 May 2019 4,691 4 View

How to display a 3 Dimensional matrix by their values in Matlab?For example if x is a matrix of size 20x15x6.How to visualize the structure in MATLAB?

For example to model a microstrip patch using FDTD. The 3D array would be of size MxNXP. How to pictorically represent the structure using MATLAB?

08 January 2019 6,765 4 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

LEDs on Vis Light photo degradation of MB water sol via N doped TiO2 in a mini flume?

Good day to all, I have no experience with light emitting diodes. I am building a glass mini flume to demonstrate the photo degradation of Methylene Blue in water running over self cleaning...

26 February 2021 4,026 5 View

Can anyone share his experience regards Smoothing in origin?

I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...

26 February 2021 8,183 3 View

I am looking for a simple software program to model 3D chemical bonds. The purpose is to generate high-quality graphical abstracts. Any suggestion?

Hello everyone: I am looking for a simple software program to model chemical bonds. The purpose is to generate a high-quality graphical abstract for a top leading journal in the field of...

23 February 2021 8,012 3 View

How to construct different filler shape in MD simulations?

Is there any way to construct different initial filler shapes like triangle, square, rectangle, pillar, and tube in any simulation software.

20 February 2021 1,750 1 View

Blast analysis of RC,UHPC slabs using material model *MAT_72R3 in LS-DYNA?

20 February 2021 5,984 3 View

How to model in HFSS or FEKO Free Space Material Characterization?

I am having trouble setting up this problem in HFSS or FEKO. In HFSS, I've tried both FEM and FEBI-IE solvers. With FEKO, I've tried it's MoM solver and default settings. I am would like model...

09 February 2021 375 2 View

Which method need to be used to predict crack propagation?

Need to predict the crack propagation phenomenon in a CI component. Suggestions are needed regarding the the methods ( XFEM, J integral, etc.,) which will predict the crack propagation behavior...

06 February 2021 1,936 4 View

Is it possible to find out the wettability and contact angle of water on the rough or corrugated substrate?

First of all, whether it is possible to identify the presence of water and its amount on the Silicon substrate by using only FT-IR spectroscopy. Can ATR-FTIR spectroscopy find out the wettability...

03 February 2021 9,085 4 View

In your view, which current SEM is most recommended for EBSD/TKD and EDS analysis?

I know that this is a very difficult question, as the areas of application can vary greatly. However, if you want to operate low as well as high resolution (from a few millimeters to nanometers),...

02 February 2021 4,985 4 View