How much change in hot and cold formability will be there if alloys with poor fomabilty is forged or rolled under vacuum?

Some of alloy steels and superalloys have very small forging window and one faces problem of cracking during hot forging and rolling and are preferentially isothermally forged.It could be...

27 January 2020 2,548 2 View

How we can determine critical temperatures like ac1,ac3,Ms Mf and liquidus temperature of a steel alloy by thermo mechanical simulator?

In my experimental alloy I want to calculate the actual critical temperatures of alloy steel like ac1.ac3.Bs. Bf, Ms,Mf,liquidus and solidus temperature by TMS GLEEBLE 3800.This will help me in...

15 May 2018 6,312 7 View

Titanium or Tantalum?

19 August 2014 170 7 View

Can we use S/N analysis for Full-factorial experiments?

We are planning to conduct full factorial experiments. I found in most of the literature that the analysis associated with Full Factorial experiments is ANOVA based on coefficients. I wan to know...

30 July 2014 7,835 4 View

Do we have to follow the sequence of experiments while performing experimentation in Taguchi methodology?

Can we perform all those experiments which are at one level and then move to the other? For example: There are three levels of cutting speed - 1000m/min; 2000m/min and 3000m/min; 1000m/min setting...

20 March 2014 4,991 3 View

How to simulate mobile agents using castalia?

Dear Researcher, I read your paper bench mark itinerary algorithm, the survey is done excellently, could you please guide me as how to use castalia for simulating mobile agents.

01 January 1970 8,905 4 View

Waters 2707 HPLC autosampler problem?

I am using a 2707 waters HPLC device. When I try to inject a sample, it says missing plate or rack. I changed the needle and calibrated its position but I still get the same problem. I even get...

02 March 2021 1,408 1 View

Should we change media after1st 6hrs after plating HUVEC bought from INVITROGEN?it's not recomended by invitrogen.Will DMSO present in stock matter?

We have HUVEC bought from Invitrogen. Cat no -C-003-5c. while first plating the cells we have bought the protocol suggests not to centrifuge the cell with media to remove the DMSO. Should we...

02 March 2021 3,713 2 View

How to normalise data on OPM package from R Studio ?

Good afternoon, I recently used OmniLog from BIOLOG for my experimentations : I tested the metabolism of different strains on 2 types of plates. I have 16 strains of 3 different groups...

02 March 2021 3,584 1 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

Benefits of the 24 welled plate?

We have always used the 96 welled plate, the 48 welled plate but apparently there is much evidence on the 24 welled plate and above all its benefits.It states it is the same you would use on ELISA...

28 February 2021 1,149 1 View

Can bacterial suspension be pipetted directly onto petri dish and agar poured onto it?

Hi, recently I encountered a protocol for plating which was not the usual method I have been practicing (pour LB agar onto plate, allow it to solidify, pipette bacterial suspension onto plate,...

28 February 2021 7,292 3 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View