If I use RF and DC sputtering for same conductive target, says metals target does the expected rate of deposition may differ?

Santhoshkumar Mahadevan @Santhoshkumar_Mahadevan

08 August 2015 0 9K Report

If it is differing due to AC current shall I take deposition rate is exactly half of DC?

Badges
Science topic

More Santhoshkumar Mahadevan's questions See All

I just want to know factors affecting crystallite size of a materials?

Same metals i am trying to synthesis with same procedure and same condition but i am not able to achieve same X-Ray crystallites size using Scherrer relation or caglioti relation. In each and...

03 April 2016 5,568 14 View

• What the possible Persistent Organic Pollutants and Heavy metals present in fluorspar, sediments, and water bodies around its mining area?

Approximate concentrations are require in compared with the WHO permissible limts

11 August 2024 2,723 1 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

How can I find access to heavy metal reference doses from the EPA and WHO websites?

Reference dose and Maximum acceptable concentrations HMs

03 August 2024 8,230 4 View

How to scrape off the surface layer of compound sputtering targets as with multiple usage top layer's stoichiometry changes from the original target?

I am experiencing this for the Bi2Se3 sputtering target. Initially, even if the target was 2:3 in Bi : Se, with a few sputtering runs, due to the high escaping tendency of selenium, the top layer...

23 July 2024 1,649 1 View

Optimal condition for depositing FTO target 95:5% using sputter technique?

Hello I want to know about the sputtering condition of depositing FTO from target 95:5%. I tried with RF sputter in pressure 2.5Pa and 100 sccm Ar at room temperature but it showing no...

21 July 2024 1,680 2 View

How can we reduce the porosity of tungsten oxide (WO3) thin films during DC sputtering deposition (target: W, power: 100 W, 75 W, and 50 W)?

We are fabricating a tandem structure where a ~50 nm thick WO3 film is deposited between two metal films using DC sputtering. We use a mixture of Ar and O2 gases at different flow rates while...

01 July 2024 2,686 2 View

Why hall bar fabricated using photolithography and sputtering are not showing continuity with contact pads?

I am fabricating the Hall bar (5 micron width and 35 micron length) of Ta(3nm)Co(4nm)Pt(5nm) using photolithoghaphy and sputtering. This Hall bar is connected by contact pads of Ti(10nm)/Au(60nm)...

29 June 2024 2,079 3 View

How to conduct bio accessibility analysis of Heavy metals?

for estimation of human health risks

26 June 2024 7,326 3 View

How to prepare polyaniline emeraldine salt ( PANI -ES) sample for Transmission electron microscope (TEM) analysis?

I need to do TEM analysis for my Polyaniline emeraldine salt form. May I know which solvent is appropriate for preparing TEM sample?

25 June 2024 9,086 3 View

How to solve the problem that the film obtained by magnetron sputtering on the ternary alloy target A2BC is ABC (not A2BC)?

Using magnetron sputtering with an alloy target composed of A:B:C in a 2:1:1 ratio, the resulting thin film composition is A:B:C=1:1:1. How can you achieve a A:B:C=2:1:1 composition? What are some...

24 June 2024 1,605 0 View