I would like to know , how to generate the tool path in abaqus software????

Vignesh Azhagarsamy @Vignesh-Azhagarsamy

29 December 2019 0 2K Report

I am doing my project in single point incremental forming. Here how to apply the BCs and the tool path in the Abaqus software.

If anyone has done this, please lend me the amplitude or the CAE File.

thank you...

Badges
Science topic

More Vignesh Azhagarsamy's questions See All

XRD Analysis is showing only Calcium carbonate. It is not showing other compounds. Can anyone help me get the other compounds?

XRD Analysis is showing only Calcium carbonate. It is not showing other compounds. Can anyone help me get the other compounds

04 August 2024 3,019 3 View

In XRD analysis using Xpert highscore plus software I am getting error as Index < 0 or Index >= NrOfDataPoints. in K alpha2 value..can anyone help?

In XRD analysis using Xpert highscore plus software I am getting error as Index < 0 or Index >= NrOfDataPoints when entering K alpha value. Because of that I am not able to find the peaks...

11 June 2024 4,018 2 View

Can anyone guide me with the selection of good begineers pc or laptop specifications for computational calculations like quantum expresso, vasp?

I am new to computational calculations and it is very difficult to select a pc or laptop for quantum chemical calculation. It would be great if anyone just give me a list contains specified type...

09 June 2024 4,988 2 View

How can i be able to calculate the residual stress of xrd data using xpert high score plus?

I have a xrd data of a sample to be analyzed for calculating its residual stress. Any suggestions might be helpful

19 March 2024 942 3 View

Need information of Next-generation sequencing (NGS)?

Greetings of the day, Dear Friends, I hope you are doing well. Kindly discuss the general pipeline/methodology/steps to do Next-generation sequencing (NGS). Can Anyone tell me where i can learn...

07 March 2024 555 4 View

Regarding methanol to dimethyl ether kinetics on hzsm-5 ?

Hlo I am trying to get kinetics of methanol to dimethyl ether kinetics on hzsm-5 si/al = 40 catalysts at 160 deg c I was unable to reach zeroth order kinetic regime. I doubt that the reaction will...

05 March 2024 7,671 1 View

Rietveld refinement of two phase pattern ?

Hello everyone, I am trying to run Rietveld refinement on my sample which has two phases. The primary phase is quite dominant with most of the peaks, but there is only one peak of the secondary...

04 March 2024 9,832 2 View

On what basis do I use specific capacitance or areal capacitance?

Research papers on SCs mention capacitance in terms of both specific and areal capacitance. How does one decide which one to use while reporting? Thanks in advance

28 January 2024 5,721 1 View

I want to perform GCD for Supercapacitor Devices, for that can any one suggest specific current and specific capacitance formulas?

I want to perform GCD for symmetric as well as asymmetric supercapacitor devices. In that regard, can anyone suggest specific current (consideration of the mass of one or the sum of two electrode...

28 January 2024 3,677 1 View

Which is the suitable protein-protein interaction data analysis method/platform for identification of targets from MS/MS?

I have a list of identifiers/hits processed based on log fold changes. I tried using pantherDB to generate GO terms and cytoscape for network construction. I need a clear picture on how to...

02 January 2024 8,770 2 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

How to start a Molecular Dynamics Simulation?

Is it possible to conduct a molecular dynamics simulation to see the effects of a specific carbohydrate on the structure of lipids (e.g., micelle structure)? I am a beginner in this field and plan...

03 August 2024 3,371 3 View

Which will be the best software for the Hydration shell analysis with molecular dynamics?

I am using a windows system, what software I should use for hydration shell analysis with molecular dynamics?

02 August 2024 3,143 4 View

Can we patent a process flow diagram developed using a process simulator but no actual cases is carried out?

Can we patent a process flow diagram developed using a process simulator but no actual cases is carried out? For example consider a process for certain product manufacture where a new process flow...

31 July 2024 781 1 View

Simulation of metal drawing by Abaqus with UMAT?

Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...

30 July 2024 7,062 1 View

Why running a restart analysis in Abaqus in Ubuntu OS gives an error as attached when running the same job in Windows doesn't give any error and runs?

I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...

29 July 2024 9,572 3 View

How to restart MD without using checkpint file in GROMACS?

Dear All Gromacs User I would like to restart MD without using checkpint .cpt files? I heard there is a way for acheiveing this. Any input and sugegstions are most welcome. Thanking You Budheswar

29 July 2024 3,084 8 View

How Can I Apply Hashin Damage Properties to Solid Elements in Abaqus Without Using VUMAT?

Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...

28 July 2024 8,169 0 View