I need experimental data for validation of desorption langmuir kinetics model?

More Ayuob Aghaei's questions See All

What standard you suggest, to measure the fluorescence quantum yield with excitation wavelength of 400 nm?

I synthesized nanoparticle with fluorescence excitation wavelength of 400 nm and emission wavelength of 450 nm. Therefore, to measure the quantum yield, we should use standards that have an...

04 May 2016 4,189 6 View

What are your thoughts about the XRD peak (attached)?

I intended to synthesise carbon dots using bottom-up methods. Similar carbon dots, my product is yellowish brown and it has excellent blue fluorescence and Tyndall effect, but I don't take peak...

09 October 2015 3,419 6 View

Do you think these pictures can be described as graphene or carbon dots or both?

I tried to synthesis graphene by the hydrothermal method. The catalyst was changed. I took photos of products (below images. Particles in Image 2 are teeny fraction same image 1. Sample 1 being...

01 February 2015 7,227 7 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Baseline drift in HPLC? What causes this?

Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!

11 August 2024 3,770 4 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How to calculate CCS for Sodiated adduct ions and Multiply Charged Ions?

I'm currently working on calculating the collision cross section (CCS) for various ions, and I'm facing challenges when dealing with sodiated and multiply charged ions. Most of the resources I’ve...

08 August 2024 8,329 0 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Fernando Vallejos-Burgos

You need to do the experiment or search in the literature for your particular system.

Ayuob Aghaei

I want only data concluded from the rest experiment. I want validate accuracy or lack of accuracy this data by my computer and MATLAB program.

Sandesh Ramesh Tetgure

I have used this kinetics model for my research and you can find my published paper explaining different kinetics and isotherm models in detail. Link for my paper is : http://www.tandfonline.com/doi/full/10.1080/01496395.2015.1064960#abstract