I have calculated the 12 switching angles and then find delays from these angles, kindly tell me how can I used the delay in multilevel inverter?

03 April 2017 0 6K Report

These delays find out from HALF Height method. I am confused that how can i use these delays in my 7 level H bridge inverter. The Switching angles and delays are gievn in below picture. the switching pattern is also given below for 7 level inverter.

Badges
Science topic

Similar topics
Correction

More Muhammad Abdul's questions See All

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

How to calculate the annealing temperature of a primer pair?

I have to amplify a gene and my primers just reached. The Tm for Forward primer is 64.2, and that of reverse primer is 65.5. Can some one suggest how to get the best annealing temperature? Thanks...

01 March 2021 360 7 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

The reason that the culture of white fungi Contamination with green mold(Trichoderma), the culture autoclave at121 for 15 min. What is it?

Is the period to autoclave not enough? The inoculation in a hood and flame and UV and alcohol.

27 February 2021 9,356 3 View

How to include original NMR data in a manuscript?

hello. i am junior researcher. I received a comment from a reviewer that he could not find NMR data in my submitted paper. I had included the NMR graph with explanation and formula to calculate...

27 February 2021 734 4 View

Does different dilution factors affect negatively on NH3 reading ?

I have a sample of treated water sample & asked to obtain ammonia conc. in sample using a machine with 5-25 ppm detection range. However, upon testing with different dilution factors, all...

27 February 2021 8,483 3 View

Can anyone share his experience regards Smoothing in origin?

I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...

26 February 2021 8,183 3 View

Physics: Why do we describe light by referring to its wavelength, but microwaves and radar pulses by referring to their frequency?

In physics, the description of the properties of light generally refers to its wavelength (nm), while in the range of microwaves and radio waves we refer to the frequency of a signal (e.g. kHz or...

03 March 2021 1,682 3 View

Is it mandatory to specify Subjects Combinations in Generalized Linear Mixed Models (SPSS)?

Hi all, I have data with two levels: lets think of the classic example of students and schools. When running the analysis in SPSS and selecting the Random Effects, we can select (we can or we...

24 February 2021 7,379 4 View

How to find natural frequency of a bridge from vehicle induced vibrations?

i have frequencies of bridge that are effected by mass of vehicle. the problem is when any vehicle pass the bridge it would add the its mass to the bridge mass ultimately mass of the bridge will...

22 February 2021 10,004 3 View

How to overcome convergence issues in concrete arch models?

Hi, I have modelled a three-span arch bridge with soil fill over along with pedestals. The FE modelling is done in LUSAS with HX8M solid elements (i.e. 3D solid modelling). The non-linearity is...

20 February 2021 1,346 2 View

Structure of the residual covariance matrix in a model with multilevel within-subject factors?

Hello, I have a dataset with a three-level structure. Participants reported an outcome of interest for 3-4 aspects of an incident, and they reported 4 types of incidents (1 incident for each...

09 February 2021 4,280 3 View

How do I connect DAB DC DC Converter to a battery in matlab simulation ?

I am trying to model a DAB converter and I need to observe the power transfeered to the load side on varying the phase shift between two bridges, hence I couldnt take a constant load e.g...

09 February 2021 6,489 3 View

Grid connected inverter using virtual synchronous machine?

Hi everybody, currently, I am working on the grid-connected inverter. I want to make my grid-connected PV system a PLL-less system. I have studied some reachers are implementing a virtual...

07 February 2021 6,078 2 View

Can we model an Arima (0,0,0)(0,0,0) with pulse intervention?

Hello, i got trouble when i try identify a intervention analysis about disaster impact on night time light intensity. i have 65 month data from January 2015 until may 2020. based on...

06 February 2021 10,018 4 View

Can anyone elaborate the method to measure arterial pulse wave velocity in research studies involving Sphygmocor??

Sphygmocor is the tonometry based instrument which is used to record generally radial pulse waves and then calculating various variables like Augmentation Index, SEVR etc. It is also used to...

02 February 2021 7,546 3 View

Can't run my IPMSM drive system with DC-supply higher than 125 V. Have anyone had similar problem?

Hey, I try to run my 4 pole IPMSM with PWSVM and use a typical controller with PI-controller with a current loop and speed loop. When I run my system with DC-supply 100 V with a steady-state speed...

28 January 2021 7,354 8 View