01 June 2023 1 2K Report

The samples are Periwinkle shells, clam shells, whelks shells and snail shells. they were chemically activated by Sulphuric acid and Potassium Hydroxide.

The SEM and FTIR imagery is required for my Thesis.

More Uchechi Akomah's questions See All
Research topic: Knowledge, Attitude and practice of household solid waste reduction at xyz LGA of a state?

Please honourable friends and colleagues I need help with calculating my sample size for this study and also what statistical analysis is best fit for this type of study? Please help me.

29 November 2022 8,889 4 View

How can I effectively extract essential oils for antioxidants, anti-inflammatory analysis?

Can I use soxhlet extractor for hydrodistillation. I don't want to use solvents.

29 June 2021 459 8 View

How do I prepare 20mg/kg body weight of artesunate tablet to mice in an antimalarial study?

I'm using artesunate as the standard antimalarial drug, I want to use 20mg/kg body weight of the experimental animals. How do I prepare this dose?

09 December 2018 4,268 3 View

Why is methanol solvent continuously used in plant extraction despite its toxicity?

Assuming an animal dies while carrying out an experiment, could it be as a result of toxicity of methanol used in extraction or the extract?

20 August 2018 8,319 5 View

Similar questions and discussions
How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Aspen Plus Simulation?

Greetings When one is to perform Simulation or modelling of Pyrolysis of Biomass Waste materials using Aspen Plus software, and one has both the macromolecules breakdown (Cellulose, Lignin and...

06 August 2024 5,023 1 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Why reactivity isn't increased with more empty spots in valence shell?

If from a geometric perspective the non-halogens, non-noble gases have more empty spots in their valence shell, and the filling/exiting of any of the empty spots in the shell constitutes a...

03 August 2024 4,787 2 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close