Ansys APDL: do Loop and vwrite ?

05 June 2016 6,863 4 View

Ansys APDL: jobname.log?

05 June 2016 5,315 1 View

Ansys GUI : 3D Meshing ?

05 June 2016 8,994 0 View

Ansys GUI : 3D Meshing ?

Hello everbody I use Ansys 16.2 and I an not experienced in this matter. I would like to get a 3D Meshing for the mass 21 element and a block geometry. Any help is welcomed, thank you Peter

05 June 2016 3,501 3 View

Ansys APDL: do Loop and vwrite?

05 June 2016 4,875 2 View

Beam Deflection, with Tut. Nyquist & Haghigh; Elements ?

05 June 2016 1,207 0 View

Ansys APDL: jobname.log?

Hello everybody, Using jobname.log (either in GUI, or typed it in) I am supposed get a list of all of my commands. But where can I find this list (in session ediitor ?) and how can print it? Any...

05 June 2016 7,286 1 View

3 D Meshing with Ansys 16.2: 3D nass 21 element with boch geometry ?

05 June 2016 6,345 0 View

Ansys APDL GUI, Response Spectrum "2D elastic3" element? ?

Hello everybody, I try to use the tutorial 6.5.3 of http://www.ansys.stuba.sk/html/guide_55/g-str/GSTR6.htm to calculate the response spectrum of a supported beam . To do this I need a "2D elastic...

05 June 2016 2,196 1 View

I gave up V12and use GUI Ansys 16.2. I wonder what is the counterpart of commands Fluid/CFD...Run Flotran?

Ansys Tutorial: Laminar and TurbulentFlow Analyses in a 2-D Duct. 29.01.2009

03 April 2016 4,689 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Can we distinguish the type of free fluid inside the pelvic and abdominal cavities whether blood or serous fluid using the ultrasound?

during ultrasound examination of acute abdomen, sometimes we see free fluid , can we know the type of fluid ,whether blood or not , using ultrasound only? if yes , what are the sonographic...

01 March 2021 7,476 4 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View