I gave up V12and use GUI Ansys 16.2. I wonder what is the counterpart of commands Fluid/CFD...Run Flotran?

04 April 2016 0 5K Report

Ansys Tutorial: Laminar and TurbulentFlow Analyses in a 2-D Duct. 29.01.2009

Badges
Science topic

More Peter Plaschko's questions See All

Ansys APDL: jobname.log?

Hello everybody; Using a jobname.log (either typed in, or File>Change Jobname) I am supposed to obtain a list of all of my commands. But where can I find this list (In the session editor ?,...

05 June 2016 5,428 1 View

Ansys APDL: do Loop and vwrite ?

Hello everybody, Using PADT-data to combine do loops and vwrite in form of /prep7Ux=1Uy=8*DO,I,1,5 ! For I = 1 to 5:XXX,I = 0.1*I ! Read XXX file I *CFOPEN,'File','txt'*VWRITE,XXX,Ux,Uy(3F10.5)...

05 June 2016 7,317 4 View

Ansys GUI : 3D Meshing ?

Hello everybody, How can I use Ansys 16.2 GUI to obtain a 3 D Meshing for a mass 21 element and block geometry? Thanks a lot Peter

05 June 2016 9,096 0 View

Ansys APDL: do Loop and vwrite?

Hello everybody, Using PADT-data to combine a simple example of a do loop and writing I put: /prep7Ux=1Uy=8*DO,I,1,5 ! For I = 1 to 5:XXX,I = 0.1*I ! Read XXX file...

05 June 2016 5,501 2 View

Ansys GUI : 3D Meshing ?

Hello everbody I use Ansys 16.2 and I an not experienced in this matter. I would like to get a 3D Meshing for the mass 21 element and a block geometry. Any help is welcomed, thank you Peter

05 June 2016 3,626 3 View

Ansys APDL: jobname.log?

Hello everybody, Using jobname.log (either in GUI, or typed it in) I am supposed get a list of all of my commands. But where can I find this list (in session ediitor ?) and how can print it? Any...

05 June 2016 7,399 1 View

Beam Deflection, with Tut. Nyquist & Haghigh; Elements ?

Hello Everybody, Using Ansys 14.5 and the element of the beam: et, 200, BEAM4: Enter and R, 200, (parameters):Enter in GUI as well as with command line operation based on the tutorial Beam...

05 June 2016 1,294 0 View

3 D Meshing with Ansys 16.2: 3D nass 21 element with boch geometry ?

Hello everybody, I used ANSYS 16.2 GUI; to obtain 3 D Meshing with mass 21 element and block geometry. Any help is welcome, Peter

05 June 2016 6,462 0 View

Ansys APDL GUI, Response Spectrum "2D elastic3" element? ?

Hello everybody, I try to use the tutorial 6.5.3 of http://www.ansys.stuba.sk/html/guide_55/g-str/GSTR6.htm to calculate the response spectrum of a supported beam . To do this I need a "2D elastic...

05 June 2016 2,304 1 View

I gave up V12and use GUI Ansys 16.2. I wonder what is the counterpart of commands Fluid/CFD...Run Flotran?

03 April 2016 7,490 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

AUX gas reading problem on QE with full MS and PRM method in one run?

Dear QE-users, In the method where full MS positive mode and PRM mode are used, we always get an incorrect auxiliary gas reading (41 instead of 25). This only happens in this method; other...

06 August 2024 4,953 0 View

People weight in Oaxaca Blinder Decomposition on R?

Hello guys! Do you have experience running a Oaxaca-Blinder decomposition on R applying person weights. How do you suggest doing it? I have a variable PERWT which gives more information on how...

04 August 2024 6,033 0 View

How to perform EEG source analysis on each trial of data separately?

Hello Everyone I have a question about structure for connectivity analysis on sources. My goal: preprocess and cut data into trials create headmodels, using template MRI file perform source...

30 July 2024 2,744 1 View

How to add Cr parameter in autodock?

When I run autogrid4 it says: autogrid4: ERROR: Unknown receptor type: "Cr" -- Add parameters for it to the parameter library first! Look forward to your reply.Thank you so much!

29 July 2024 488 0 View

CAD File of human's & rat's respiratory airways ?

Dear all, I am working on particle deposition in human's & rat's respiratory airways using CFD and I am looking for the 3D CAD file for my simulations (STEP or IGES format). If somone has such...

29 July 2024 1,092 2 View

Why running a restart analysis in Abaqus in Ubuntu OS gives an error as attached when running the same job in Windows doesn't give any error and runs?

I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...

29 July 2024 9,572 3 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

How to use Desmond in HPC ?

Our department has recently acquired an HPC (High-Performance Computing) system, and I'm thrilled to take my molecular dynamics calculations to the next level using Desmond. I used to run my...

28 July 2024 6,553 1 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View