24 Questions 3 Answers 0 Followers
Questions related from Peter Plaschko
Hello everbody I use Ansys 16.2 and I an not experienced in this matter. I would like to get a 3D Meshing for the mass 21 element and a block geometry. Any help is welcomed, thank you Peter
06 June 2016 3,605 3 View
Hello everybody, I used ANSYS 16.2 GUI; to obtain 3 D Meshing with mass 21 element and block geometry. Any help is welcome, Peter
06 June 2016 6,445 0 View
Hello everybody, How can I use Ansys 16.2 GUI to obtain a 3 D Meshing for a mass 21 element and block geometry? Thanks a lot Peter
06 June 2016 9,078 0 View
Hello everybody, Using PADT-data to combine a simple example of a do loop and writing I put: /prep7Ux=1Uy=8*DO,I,1,5 ! For I = 1 to 5:XXX,I = 0.1*I ! Read XXX file...
06 June 2016 5,476 2 View
Hello everybody, I try to use the tutorial 6.5.3 of http://www.ansys.stuba.sk/html/guide_55/g-str/GSTR6.htm to calculate the response spectrum of a supported beam . To do this I need a "2D elastic...
06 June 2016 2,282 1 View
Hello everybody; Using a jobname.log (either typed in, or File>Change Jobname) I am supposed to obtain a list of all of my commands. But where can I find this list (In the session editor ?,...
06 June 2016 5,416 1 View
Hello everybody, Using jobname.log (either in GUI, or typed it in) I am supposed get a list of all of my commands. But where can I find this list (in session ediitor ?) and how can print it? Any...
06 June 2016 7,383 1 View
Hello everybody, Using PADT-data to combine do loops and vwrite in form of /prep7Ux=1Uy=8*DO,I,1,5 ! For I = 1 to 5:XXX,I = 0.1*I ! Read XXX file I *CFOPEN,'File','txt'*VWRITE,XXX,Ux,Uy(3F10.5)...
06 June 2016 7,295 4 View
Hello Everybody, Using Ansys 14.5 and the element of the beam: et, 200, BEAM4: Enter and R, 200, (parameters):Enter in GUI as well as with command line operation based on the tutorial Beam...
06 June 2016 1,285 0 View
Ansys Tutorial: Laminar and TurbulentFlow Analyses in a 2-D Duct. 29.01.2009
04 April 2016 4,761 0 View
Workbench 16.2 translated from German to English
04 April 2016 1,029 0 View
I gave up V12and use GUI Ansys 16.2. I wonder what is the counterpart of commands Fluid/CFD...Run Flotran?
04 April 2016 7,478 0 View
Ansys Wokbrnch V12 : Create -> Boolean ?
10 October 2015 6,224 1 View
Boolean
10 October 2015 5,128 0 View
Hello everybody, I am new in Fluent flow. I used a geometry with two concentric cylinders D1=5m, D2=64m. I do not know what means frozen and needed extruded cylinders to activate the Boolean...
01 January 1970 5,133 0 View
01 January 1970 1,653 0 View
01 January 1970 4,757 0 View
01 January 1970 4,175 0 View
01 January 1970 6,392 0 View
Using correponding fluid- tutorial(J, Singleton, R. Bhaskaran) with two concenttric circles D1=5m, D2=64m. Problem 1 ) "Surface from Sketches" : does not work, Problem 2)Two circles with...
01 January 1970 6,189 0 View
Hello, I am new in Fluent flow. I tried SimCafe Fluent Tutorial ( J, Singleton, R. Bhaskaran) however I obtained difficulties with two concentric circles D1=5m, D2=64m and could not follow with...
01 January 1970 2,255 1 View
Base 0bject from Sketches: Ansys workshop Hello everybody! I am new with workshop fluent and try to model Laminar pipe flow. I used under xy-plane Sketch 1 and rectangle with H=20 m, V=5. There...
01 January 1970 6,227 0 View
Hello everybody, It appears in the PDS Tutorial for a square plate fixed on two sides, loaded in the center. What are the details to usethis tutorial. Thanks a lot, Peter
01 January 1970 4,020 0 View
Hello everybody! I am new with workshop fluent and try to model Laminar pipe flow. I used under xy-plane Sketch 1 and rectangle with H=20 m, V=5. There arise problems with Base 0bject Sketch1, I...
01 January 1970 5,509 1 View
