How to implement monte carlo method to compute state value in matlab ?

assume there are 80 states each with a possibility of 2 actions. we have a predefined reward function. The problem is about research allocation.

30 October 2020 9,930 3 View

What is the different between model, architecture, framework, and protocol in computer science?

I know this question is clear but I want to know the difference between these facts especially in computer science?

31 May 2019 5,710 2 View

Why the crack propagate in that direction (to the left hole)?

Left side of the specimen is applied with fixed support and load is applied downward on the right hole. I need an explanation why the crack propagate to left hole. What i have in mind is since...

18 February 2019 2,159 1 View

Why so called dark matter is outside the galaxy?

The so called dark matter is pictured out side the galaxy. What is the reason? why cant it be a part of the galaxy itself ?

03 September 2018 155 4 View

Can non-motile bacteria perform chemotaxis?

Most model for chemotaxis are flagellated bacteria. Im just wondering how this non-motile organisms adapt to starvation or repellent. If you can provide me some journal article that would be...

02 March 2018 9,880 3 View

Why high ROS signal in flowcytometry and fluorescence microscope?

Hello I want to investigate the effect of high temperature on ROS production in yeast. I have yeast cells which grow at 30 degree as a control and experiment cells grown at high temperature.I used...

21 April 2016 8,392 5 View

If two proteins run in sds page with different molecular weights, if both show bands with same intensity, does it mean they have same concentration?

If two proteins run in sds page with different molecular weights(having difference of 60 KDa),if both shows bands with same intensity,does it mean they have same concentration?

03 November 2015 9,304 3 View

Serum starvation in cell line treatment?

How long after seeding of cell line, should I do serum starvation or serum 4%? 24 h or less? How long should it last (before treatment) or serum 4%? 24 h or less? i i want to do serum starvation...

05 December 2014 8,834 3 View

In SDS PAGE, actin crosslinking doesn't show any significant increase in mass comparing actin bindings - any thoughts?

Can anyone help me to explain while running my protein samples in SDS PAGE, Actin crosslinking doesn't make any significant increase in molecular mass comparing actin binding protein samples.

29 August 2014 9,634 3 View

Which neuronal cell line is a appropriate selection?

Hi. I want to investigate the effect of an herbal drug for memory genes. I selected PC12 cell line. This cell line differentiates neuron-like cells after NGF treatment. Because the NGF is very...

23 July 2014 4,806 3 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View