I have tried changing compliance current, delay. But I still couldn't figure out.
24 January 2021 9,054 2 View
any suggestions for beginners ???
31 December 2020 3,055 4 View
I am asking this in relation to practice in active learning in physics education in context of Nepal's education system where we highly focus on content based and rote learning.
02 December 2020 6,686 3 View
Hi All I need your guidance on how we can combine multiple variables and develop one index. The goal is to have a index based of which we can plan for staffing. The variables are: daily patient...
21 October 2020 422 6 View
Hi, I am modelling a half model of RCC beam in ANSYS Mechanical APDL. The model I have created is exhibiting abnormal behavior at the support with abnormal cracks. I would be grateful if you...
12 October 2020 8,596 3 View
Major details about their interrelations, their major uses and functions.
22 September 2020 9,796 4 View
Does anyone have experience of extracting DNA out of dairy cow's milk? I am interested in the DNA present in the B-cells. I have done extraction from blood but want to try extraction from milk. I...
02 September 2020 3,536 5 View
Hi, I am trying to model an RCC beam in ANSYS Mechanical APDL. I have the value of Compressive strength, and modulus of elasticity of the concrete of the experiment I am trying to validate ? Can...
28 August 2020 4,623 2 View
I want to preserve bovine PBMCs for doing flow cytometry later on. It doesn't seem feasible to count PBMC cells for preservation as there will be lots of samples. Is resuspending the PBMC pellets...
07 July 2020 8,228 2 View
Is ehtical clearance mandatory for research? As far as I understand where you have sensitive design and experiments or issues related to human and animals, there only you are required to go with...
23 May 2020 538 6 View
I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...
03 March 2021 1,931 5 View
I am using a 2707 waters HPLC device. When I try to inject a sample, it says missing plate or rack. I changed the needle and calibrated its position but I still get the same problem. I even get...
02 March 2021 1,408 1 View
Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...
01 March 2021 9,332 6 View
I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...
26 February 2021 1,511 3 View
Hi, everyone I'm working on a privacy-preserving algorithm that will apply to IoT devices. So, I need to measure the power consumption by implementing this algorithm. Any suggestion, advice,...
25 February 2021 8,749 6 View
I am trying to characterize an electrochromic system. The system uses ITO electrodes on glass, WO3 as the electrochromic film, and NiO as the ion storage layer. When I deposit NiO and WO3 and...
23 February 2021 9,592 2 View
Hello researchers! While studying the literature on refractive index sensors, most of the articles simulate their devices with a refractive index ranging from 1 to 1.1, with small steps in...
17 February 2021 1,578 4 View
I tried to sweep my ferroelectric devices from -2V to 2V and then from 2V to -2V and The two hysteresis peaks are off by several microFarads. Should i increase bias voltage? I am doing these...
16 February 2021 8,514 2 View
The data collected from various measurement devices often contains erroneous values - such as noise, missing values, etc. What are the popular techniques for pre-processing measurement data in...
14 February 2021 4,642 2 View
I'm looking for ways to prevent the settling of magnetic beads in solution. I have been using a syringe pump to inject a suspension of magnetic beads in PBS into a microfluidic device, and so far...
09 February 2021 6,206 2 View