11 March 2020 3 6K Report

I readed the Bernese manual which that published at Bernese website, but it was'nt enough.

More Fereshteh Rezazad Gohari's questions See All
How can I find my published papers' total read, citation or any other scores?

How can I find my published papers' total read, citation or any other scores?

21 July 2024 9,802 3 View

Why polyacetal homopolymer is produced from formaldehyde? why not from trioxane which is solid at room temperature?

Polyacetal homopolymer is produced from formaldehyde in industrial scale. The monomer is in gasous state and it needs a tedious purification process. Trioxane is an alternative monomer for...

15 April 2024 8,622 0 View

Why a new peak has appeared in the spectrum after dye adsorption?

Why after the adsorption of methyl orange dye by my adsorbent, in addition to the color peak in 464 nm, another peak has appeared in 372nm n in theuv-vis spectrum. It should be noted that this...

10 March 2024 4,167 2 View

What is the origin of the small peak at binding energy of 75 eV in TiO2 XPS spectra?

I've observed a consistent phenomenon in TiO2 XPS spectra, which is the presence of a minor peak at 75 eV. This peak is noticeable in both commercially available TiO2 powder and in all the TiO2...

10 October 2023 7,661 0 View

How to dry polyethyleneimine coated Fe3O4 nanoparticles?

Hi all, I have synthesized polyethyleneimine coated Fe3O4 nanoparticles, before drying, the nanoparticles showed positive zeta potential, but after drying in the oven at 40 C , the measured zeta...

14 July 2023 7,045 3 View

Why electrospraying happens along with electrospinning of polycaprolactone?

Why along with polycaprolactone electrospinning, I also see electrospraying in the optical microscope images of nanofibers mat. The feeding rate, voltage and tip-to-collector distance have been...

16 June 2023 8,197 6 View

How Dissecting the rat hypothalamus?

Hello dear researchers Is it possible for someone to help me in the field of separating the hypothalamus by sending a video? Because the theory and seeing the atlas could not help me much.

02 June 2023 5,726 2 View

Why the rat Adipocyte mesenchymal stem cells dissociated after removal FBS after 24 hour?

In isolating the exosome from the rat adipocyte mesenchymal stem cells after removal of FBS, the cells were seperated from the bottom of the flask after 24 hours. Will the cells isolated from the...

12 December 2021 7,327 2 View

Why does O 1s peak shift to lower binding energy in XPS in titanium dioxide with oxygen vacancies on its surface?

I made defective TiO2 with Oxygen vacancies and I noticed the O 1s peak shifts to lower binding energy compared to the pristine TiO2. How Can I explain that?

07 November 2021 6,159 5 View

Why are there two main peaks in carbon monoxide IR spectrum?

I am doing CO adsorption experiment. When I collect the CO gas phase spectrum there are two peaks for CO. One at around 2114 cm-1 and the other one is around 2170 cm-1. I don't know the reason why...

16 August 2021 8,843 3 View

Similar questions and discussions
How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Is this website real?

Is this website real? https://isar.org.in/event/registration.php?id=2434532

08 August 2024 484 1 View

U you think We need a website software of Blackbody radiation law expert software?

A website software of Blackbody radiation law expert software can used through the following web site. http://39.105.188.151:3000/index

07 August 2024 1,706 0 View

Gromacs first step of minimization ?

I have face this problem anyone help me how to solve this issue ?which is below Fatal error: There are inconsistent shifts over periodic boundaries in a molecule type consisting of 78 atoms. The...

07 August 2024 2,598 1 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

Hello Everyone ! I'm looking for a good journal to publish my manuscript with low publication cost?

I am Looking for a Science Journal with good impact factor and low publication cost to publish a review paper. Your suggestions would be appreciated.

06 August 2024 6,796 3 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close