I am interested in using HORTSIM, how can I do this?

More Aaron I. Velez-Ramirez's questions See All

Can someone help with the instrument configuration in Profex using Rietveld Refinement?

I am trying to configure the instrument in Profex but I can't get a chi-squared value below 9.65 for LaB6. This is the configuration of the equipment, which is a Bruker D8 Advance with a Linxeye...

14 July 2024 4,767 1 View

Are there any information about protocols of CRISPR in leishmania strains?

I am looking for a CRISPR protocol for application in leishmania strains

08 July 2024 9,732 1 View

¿ Algún experto en simulación de inversores ?

Simular una topología de inversor para aplicaciones de vehículos eléctricos en el software PSIM

20 June 2024 2,490 0 View

How can I report grams of dry weight or dry sample of a plant extract that was concentrated and then freeze-dried?

for context, they are methanol/water extracts that were concentrated in a rotavapor and then freeze-dried. thank U.

09 May 2024 9,941 3 View

Is it wrong to add one more author over the limit imposed by the journal?

Hi, my team and I want to publish a paper. However, the journals we are overseeing for possible submission only accept 3 authors and we are 4. Would it be wrong or prone to desk rejection if we...

16 April 2024 3,945 4 View

Optimal concentration of IL-6 for stimulation?

Hi! I'm trying to stimulate cells with IL-6 (in order to perform a qPCR) but i can't find a proper protocol. Any suggestions?

03 April 2024 379 3 View

¿Cómo ha afectado el impacto del avance de las TIC en el ámbito del trabajo social?

Con esta pregunta se pretende saber los diferentes cambios que ha producido las TIC en estos últimos años en diversos aspectos de la vida relacionados con situaciones cotidianas en el Trabajo Social.

11 March 2024 8,740 2 View

¿Qué recursos son necesarios en Servicios Sociales para tratar de eliminar barreras de acceso laboral en personas con discapacidad?

Con este planteamiento se pretende hacer reflexionar a los lectores de los diferentes planes de actuación, medidas y otros tipos de propuestas que pueden ser implantados en los Servicios Sociales...

10 March 2024 1,481 4 View

¿Qué actuaciones faltan para favorecer una garantía de derechos de las personas en situación de dependencia y/o sus cuidadores?

Con este planteamiento se pretende que los lectores tomen conciencia del enorme problema social que supone en la sociedad andaluza que una persona se encuentre en situación de dependencia. De los...

10 March 2024 6,151 3 View

Are there any studies or journals relating bureaucracy with the evangelical church?

I'm soon to begin working on my master's thesis on the bureaucratic processes in the evangelical church and the threat they pose to spirituality. I was curious to know if there's any studies...

24 February 2024 4,303 1 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Who of all of you will help TPEOM to re-originate the Earths atmosphere to it original 5 atmospheric elements/gases?

Global ‘Weather’ has stopped, as ‘aqua thermionic instituted by the ‘Global thermo atmospherics has instituted global thermodynamics of 120º C + and thus all waters are, or have boiled into a...

06 August 2024 8,716 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View