we produce soft contact lenses with cast molding method ,
the material is SiHy ,
I need to know more about the hydration process,
type of water , temperature and time
we use of water bath .
BR
Masoud,
Additionally, I welcome any general advice and suggestions you may have.
11 May 2024 5,419 1 View
What are the key and important parameters in the design of switches based on photonic crystal? How can we have an ideal switch?
09 May 2024 7,074 2 View
What is the effect of refractive index changes on the output wavelength of all-optical sensors?
30 April 2024 540 1 View
In the structures of combined rings, it is difficult to have completely symmetrical rings due to the delay in response time. Also, it is very difficult to reach a quality factor above 5000 in...
23 February 2024 1,222 4 View
Dear researchers, as you know, the subject of severe plastic deformation (SPD) methods (ECAP, TT, HPT, ARB and so on) or ultrafine grained metals has been researched on for over 20 years. But I...
16 February 2024 1,096 3 View
I have been recently working on abiotic stresses (drought, high temperature, salinity and cold) responses in wheat (Triticum aestivum) using meta-analysis of transcriptomics (microarray) data. The...
04 February 2024 1,751 1 View
Dear researchers and experts, I've been investigating different testing methods for refractory bricks with special shapes. There are a few methods and standards for testing refractories; I wonder...
07 January 2024 831 3 View
Hello everyone, I'd like to inquire whether frozen tissues are suitable for use as samples in flow cytometry experiments? Your insights and experiences are highly appreciated.
28 December 2023 596 4 View
Hi all, I possess several scFv DNA sequences and aim to generate soluble forms of these single-chain antibodies to assess their biochemical characteristics, such as binding affinity and...
18 December 2023 2,070 0 View
how can i interpert XRD peaks after doping LDH. pure sample matched with JCPDF file as in papers, but after doping newly peaks appear and peaks disappear?
06 November 2023 2,674 2 View
Hello everyone! I observed in my culture (htert-RPE1 cells) an orange- red particle at the bottom of the dish. It is visible to the naked eye as a very very small red dot. Could it be a...
09 August 2024 2,824 3 View
is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it
06 August 2024 947 1 View
I am using a windows system, what software I should use for hydration shell analysis with molecular dynamics?
02 August 2024 3,143 4 View
I am looking to purchase a photography kit for onsite metallurgical investigations, such as capturing photos of worn areas, hot tears, cold tears etc. Could anyone suggest me a good...
22 July 2024 3,490 2 View
I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...
16 July 2024 3,212 5 View
These fungal slides are isolated from cultured Bread mold on PDA media and smear is treated with Lacto phenol Blue dye ..
13 July 2024 9,701 1 View
Hello everyone, I am currently working on a project involving spatial transcriptomics on E14 mouse embryos. We need to perform cryosectioning without fixing the embryos. Here is the protocol we...
10 July 2024 5,985 0 View
Hello everyone, I am trying to encapsulate an essential oil in the liposomes using the heating method and encountering some issues. I am following the protocol described below, but my solution...
10 July 2024 4,083 3 View
I am preparing polycrystalline diamond (PCD) with tape casting. The powder is 8~12 um. After drying of tapes, I place several tapes in Ta cup without warm-pressing. Next, debinding is carried...
23 June 2024 7,758 2 View
I did a frozen section of mouse brain tissue with immunofluorescence staining. My partner and I did c-fos staining together. We used different primary and secondary antibodies for different...
20 June 2024 8,989 1 View