What is the reason of collapse of water tank shown in the attached you tube?

https://www.youtube.com/watch?v=WLEkC_JbTsQ

03 April 2017 1,021 2 View

No title

02 March 2017 8,545 19 View

Why do BS8007 specify the allowable crack width of water retaining structure as 0.2mm for severe or very severe exposure?

Why 0.2 mm crack width?

02 March 2017 9,166 3 View

Which type of multiple-cell box girder is better, cells connected by top flanges or cells connected both by top and bottom flanges?

How we can design box girder bridge?

02 March 2017 9,977 3 View

What is the effect of rusting on steel reinforcement?

How does rust affect on the bonding between steel bars and concret?

02 March 2017 3,267 10 View

What is the difference between working stress approach and limit state approach?

02 March 2017 415 2 View

It is not necessary to design nominal reinforcement to piles. Is it true?

Can we use same code provisions of columns for piles?

02 March 2017 7,705 3 View

In carrying out compression test for concrete, should test cubes or test cylinders be adopted?

Relation between cubes and cylinder

02 March 2017 5,645 4 View

If concrete compression test fails, should Schmidt hammer test be adopted as an alternative test to prove the concrete strength?

Non destructive tests

02 March 2017 5,232 31 View

What is the meaning of P-delta analysis?

Some codes provisions refer to this type of analysis.

02 March 2017 8,549 5 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Glass fiber content in a gypsum board ?

Any idea on how to get the volumic ratio of glass fiber in a gypsum board ? Thank you for your help !

01 March 2021 2,501 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Complex wave form in ANSYS?

Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...

27 February 2021 5,969 1 View