Which DL architecture is better to work on handwritten data?

I am working in the area of Handwriting recognition for Bangla. As there are many DL architecture, I am confused which one to select.

15 February 2021 4,996 1 View

How to Import .inp file from abaqus CAE to Ansys perfectly?

I am trying to import an Abaqus .inp file to Ansys but it does not import the whole assembly but only imports a single part. How to solve this.

17 January 2021 5,450 3 View

Which third party CFD Codes can be used for FSI Co-Simulation in Abaqus ?

Since Abaqus CFD is no longer available in newer versions what are other available codes for Fluid-Structure Interaction Simulation

11 January 2021 2,012 3 View

How to determine Viscoelastic and Hyper Elastic Material Properties for Abaqus by mechanical testing ?

I am studying about Impact load resistance property of Polyurea (Elastomer). With respect to this, I need to conduct tests on this material to evaluate its material model behavior as a...

29 December 2020 2,969 1 View

How to simulate the energy yield of an Organic PV module based on the Temperature effects and the albedo effects?

26 December 2020 4,280 5 View

Anyone interested in joint work on writing a review article?

I a writing a review article on cancer work through Mathematical modeling. If anyone interested in this work, kindly let me know

13 December 2020 7,585 10 View

One diode equivalent circuit for OPV always has a coupled variable in the end. How to find the Power with diff. temp and diff. Irradiation values?

I am writing my master thesis to simulate Energy Hatvest of OPVs in A year. Any advice on the same would be helpful.

03 December 2020 8,915 1 View

How to create a Voltage Heat Map of distribution network?

I am trying to create a voltage heat map of a distribution network in Matlab/Python. I have the values of bus voltage magnitude and angle but cannot plot them in a heat map. The objective is to...

02 November 2020 3,561 6 View

Fund for APC?

Is there any organisation or individual who funded for journal APC? The manuscript is related to Mathematical Modelling of chemo-cancer interactions.

30 October 2020 1,796 3 View

What are the best markers for Erythropoiesis in mice?

What are the best markers for Erythropoiesis in mice? There are several markers like CD45, CD34, CD117, CD105, CD235a, CD71 based on specific stages of erythropoietic cells. Which of the above or...

19 October 2020 3,303 8 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Complex wave form in ANSYS?

Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...

27 February 2021 5,969 1 View

Any specific pipeline or parameter to analyse total transcriptomics study of brain tissue samples?

I have two groups of brain samples, control and treated for example. It was total RNA nova seq sequencing. I tried all the available pipeline like: star+rsem+deseq2, Hista+stringtie+cuffdiff,...

27 February 2021 356 6 View