Fanz-Kyldesh Effect (FKE) is an electrical-field dependent effect, which may need photon absorption model or negative gain model in TCAD. Can i demonstrate FKE effect in SILVACO ATLAS or any luminous model. Please suggest me.
im working on it still I didn’t find and software which can be able to do simul work of Quantum Dot Light Emitting Transistors Mukul Kumar
Which solution reveals the microstructure and features of nickel-based alloys?
02 March 2021 2,221 3 View
Light is inevitable for the process of photosynthesis reaction. Naturally sunlight plays the vital role for this process. Light may be of different colours like white, red, yellow, blue etc....
02 March 2021 7,890 2 View
Which tools can be used to generate machine codes for additive manufacturing?
02 March 2021 7,220 2 View
I am searching for a good place for the Post Doc,
02 March 2021 4,053 3 View
Working on chandrayaan-2 DFSAR data, there are three datasets available: 1) Slant range image data product: The slant range complex image file. Each pixel is represented by two 4-byte floating...
02 March 2021 8,481 3 View
I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...
01 March 2021 395 3 View
Hello, The Cranet website does not provide any lead to the data obtained from their multinational survey on HRM practices. Any help on accessing the data would be most appreciated. Thank...
01 March 2021 9,536 3 View
There are different kinds of food stuffs which we intake daily according to our requirements. Carbohydrate, protein, fat, mineral, vitamin, water are mainly working for the growth and development...
01 March 2021 831 2 View
I have to amplify a gene and my primers just reached. The Tm for Forward primer is 64.2, and that of reverse primer is 65.5. Can some one suggest how to get the best annealing temperature? Thanks...
01 March 2021 360 7 View
Is there any book chapter/book, webpage or research article available to understand genome-wide gene identification?
28 February 2021 8,095 1 View
I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...
03 March 2021 1,931 5 View
I am using a 2707 waters HPLC device. When I try to inject a sample, it says missing plate or rack. I changed the needle and calibrated its position but I still get the same problem. I even get...
02 March 2021 1,408 1 View
Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...
01 March 2021 9,332 6 View
I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...
26 February 2021 1,511 3 View
Hi, everyone I'm working on a privacy-preserving algorithm that will apply to IoT devices. So, I need to measure the power consumption by implementing this algorithm. Any suggestion, advice,...
25 February 2021 8,749 6 View
I am trying to characterize an electrochromic system. The system uses ITO electrodes on glass, WO3 as the electrochromic film, and NiO as the ion storage layer. When I deposit NiO and WO3 and...
23 February 2021 9,592 2 View
Currently, I am working on a project in Sentaurus TCAD for which I required the plot of Surface Potential Vs Gate Voltage. Can anyone help me finding the simplest way or a different procedure for...
18 February 2021 1,213 2 View
Hello researchers! While studying the literature on refractive index sensors, most of the articles simulate their devices with a refractive index ranging from 1 to 1.1, with small steps in...
17 February 2021 1,578 4 View
I tried to sweep my ferroelectric devices from -2V to 2V and then from 2V to -2V and The two hysteresis peaks are off by several microFarads. Should i increase bias voltage? I am doing these...
16 February 2021 8,514 2 View
Hi Can anyone please suggest me how can I study the parameters of solar cells made of graphene oxide and any other organic material composite using SILVACO. I would also like to know how I can add...
15 February 2021 5,795 3 View