How to calculate the crystallinity of cellulose film?

27 February 2021 2,753 4 View

How does GROMACS calculate the average structure of proteins?

I want to get a average structure from a pdb file containing multiple models. I used the command below: gmx cluster -f input.pdb -s topol.tpr -cutoff 20 -method gromos -av GROMACS...

25 February 2021 6,314 1 View

No title

The regenerated cellulose film was prepared by zinc chloride/H2O system. The zinc chloride had been washed away in the regeneration process, and the wet film which was not dried had uniform...

18 February 2021 9,538 1 View

R/Python package for time-intensity or progressive profiling in sensory evaluation?

Hi I've been looking for a stat package for my sensory evaluation data (progressive profiled which is a multi-timepoint version of descriptive analysis). Is there any available one to...

08 February 2021 9,170 3 View

How can I make sure the simulation results of the water droplet impacting on the wall using the FLUENT agree with the experimental results?

Dear researchers, I am modeling the process of the water droplet impacting on the wall with a constant contact angle. The specific calculation parameters are as follows: The droplet diameter is...

24 January 2021 1,020 5 View

Mysterious line across SDS gel?

Does anyone have the similar issue? A line across the denature SDS gel shows up after staining with Coomassie blue and there are many lines in every lane if you take a closer look. This gel had 15...

07 January 2021 5,610 4 View

How can I calculate packing density of particles by fomulas or softwares?

I have all data of particles, such as size distribution, or numbers. Is there any way that I can calculate the packing density of these particles? Assume that all particles are circular.

05 January 2021 4,272 2 View

After cellulose is regenerated in water, a cellulose hydrogel is formed. I want to know if there is crystallinity inside the the hydrogel?

After cellulose is dissolved and regenerated in water, a regenerated cellulose hydrogel is formed. I want to know if there is crystallinity inside the hydrogel, or it will not crystallize until it...

04 January 2021 7,466 4 View

How can I fix the density of system in coarsed grain simulation?

In the process of obtaining the nonbond potential of the Coarse-grained(CG) model, I need to simulate the CG model mapped from the conformation of all atom(AA). AA simulation process is...

02 January 2021 3,643 1 View

How to export Mass and Stiffness matrices using Ansys Workbench?

Hello, I am trying to export Mass and Stiffness matrices using Ansys Workbench via Modal analysis modular, with APDL commands inserted. However, there is no .matrix file generated. Could anyone...

17 December 2020 1,196 5 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View

Which is a lucid standard comprehensive book to guide on psychological scale construction and its standardization?

02 March 2021 7,082 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

How to choose ANN number of hidden layers and nodes?

Hello, Could you please share any interesting research explaining how to choose the number of hidden layers and nodes per layer in case of regression problems using ANN? Thank you, any help would...

01 March 2021 6,200 3 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

PUC19 as a transfer plasmid for lentiviral delivery?

Hello, Is it possible to use pUC19 as a transfer vector to be packed in using the second generation viral particles packaging system( pMD2.G; psPAX2 plasmids)? As far as I understand it there is...

28 February 2021 4,868 2 View

How could I take into consideration the weights of observation in a system of seemingly unrelated regressions (SUR) in rstudio?

I build a model of 4 regression equations (probit and OLS) in R studio. I need to take the weights of observations into consideration. While it is simple to do so for every regression equation,...

27 February 2021 1,233 1 View

What are the application of Fixed points thoery in Chemistry.?

It is said that fixed point theory has lot of applications not in the field of mathematics only but also in various areas. So I am looking for applications in Chemistry only..

26 February 2021 3,533 1 View