How to submit a fluid co-simulation interaction job from the command line in abaqus?

Ganesh Persaud @Ganesh-Persaud

21 January 2017 1 8K Report

The picture in attachment shows the prompt I'm getting. How can I submit the job from the command line in abaqus?

Romain Rieger

Hi Ganesh,

Have a look at the documentation:

http://abaqus.software.polimi.it/v6.13/books/usb/default.htm?startat=pt01ch03s02abx04.html

Classical command line (in linux command shell):

abaqus cosimulation cosimjob=cosimjob_name configure=config_file_name job=nameJob1,nameJob2 input=nameInputFile1,nameInputFile2 cpus=1,1

The tricky point is that you absolutely need a config_file.xml

In this file the name of the jobs should be the same as the one written in the command line "nameJob1" and "nameJob2". I suggest you take the one generated by abaqus when you run the cosimulation from the cae, then you just modify the name of the job and submit the whole by command line in a shell console.

I hope this will help you.

Romain

Badges
Science topic

More Ganesh Persaud's questions See All

Which is the best wavelength to study aerosol optical depth(AOD) related to climate reseach,which criteria must be adopted in choosing the wavelengh?

We are doing a study on impact of aerosol on precipitation. Which satellite data and which wavelength will be the best. or can some one suggest a criteria to be adopted to choose an instrument...

12 February 2021 6,324 3 View

Let me know whether the DOI issued by the research gate will be accepted by the anna university?

As per the rules and regulation DOI is needed and paper has to be opened in online by the anna university rules let me know whether the published article in some journal and the DOI issued by...

27 November 2020 7,540 2 View

What are the alternative way to identify the stem cells present in cord blood??

commonly used practices for the identification and characterization of the kind of cell in cord blood other than Flowcytometry and reverse-transcription polymerase chain reaction (RT-PCR).

08 August 2020 6,881 3 View

What is the difference between Hex Dominant and Cut Cell Meshing methods in CFD?

Though both the methods look similar I believe there may be differences in them. What are the disadvantages of cut-cell meshing method and why is not widely used in research in comparison with...

12 July 2020 5,636 3 View

Does anyone have GS-990 DIW EIW water filtration equipment from Advantec Japan?

I tried to contact [email protected] but no response so kindly help me in this regard. We have an Advantec GS-990, it was purchased a long time ago from a Korean Collaboration. Currently,...

16 June 2020 9,890 1 View

What is the difference between anionic and cationic redox probes?

I have done Kinetics study of two different probes namely Fe(CN)63-/4- and Ru(boy)2+ on glassy carbon electrode. I kept the potential between -0.2 to 0.6 and 0.8 to 1.2 respectively. In FeCN when...

25 April 2020 3,364 10 View

Is SIMSCALE software a good to go option for visualizing and understanding academic concepts?

On what scale can SIMSCALE simulation software be helpful for students in their engineering course work comprising CFD ( Computational fluid dynamics ), thermal and structural concepts? Can...

29 March 2020 2,952 3 View

Is the Reference Intensity Ratio of Martensite(7.98) and that of Austenite (10.81), standardized against corundum, constant?

I came across the RIR value of Martensite in a paper, which is 7.98. Similarly for Austenite, which is 10.81. I want to quantify Retained Austenite in my heat treated samples. I am using Reference...

26 February 2020 9,401 2 View

Can a thermoelectric material may have negative lattice thermal conductivity?

I have calculated electronic components of thermal conductivity by wiedmanfranz law. Then the lattice thermal conductivity is derived from it. But some of those values are negative. at the end of...

26 January 2020 1,507 4 View

Anyone familiar with protein family with highly conserved C-terminal BUT very DIVERSE N- terminal, within same protein family?

Hi friends, I have been analyzing a protein family, called Fibrinogen domain related proteins, commonly called FReD or FREPs. I confronted with problem that C terminal part of this family proteins...

08 January 2020 1,320 1 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Which cell line should we use to perform biological dosimetry experiments?

We are preparing some experiments based on irradiating cells under different conditions in order to evaluate the effects in terms of DNA damage, genetic expression, etc. As our project is...

01 March 2021 3,355 3 View

Is it possible for two human neuronal cell lines to have different gene sequence for the same protein?

I am looking at the ATP1A2 (Sodium/Potassium ATPase alpha subunit 2) in two human neuronal cell lines. Expression levels of this protein seems to be almost equal when detected by one antibody....

01 March 2021 3,607 3 View

How to assign different material properties to each element in Abaqus ?

Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...

01 March 2021 9,511 3 View

Is CD44 degraded in lysosome together with hyaluronan after CD44 mediated endocytosis of hyaluronic acid?

Also when RHAMM binds hyaluronic acid, they get internalized, will RHAMM also be degraded? Or both CD44 and RHAMM will be transferred back to the cell membrane? Asking for breast cancer cell line...

01 March 2021 8,169 2 View

Do you need the CMV enhancer before the CMV promotor for a proper function of CMV on the gene that follows?

I'm a student and I have to produce a cell line with a knockin for the NRF2 gene with GFP. I have to put a promotor in front of the GFP because the gene will be too far away from the promotor of...

28 February 2021 7,127 2 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View