I have tried crystallization by freezing the black solution in a freezer (-20oC).
I do not know what is black titanium, but I guess the density of these two components may be different. You may try centrifuging or magnetic separation..... a crude idea!
Sir, I want to work on the laser assisted machining (turning) of Nickel Based Super alloy. Please help in finding the laser assisted machining facility in India. Thanks and regards
02 July 2024 2,086 2 View
Can you please suggest it structural view and I want to calculate Power Dissipation, Delay Read SNM, Write SNM, write Access time, Read Access time, Read current. can any one suggest procedure...
15 February 2024 5,964 0 View
I have done parametric study in Ansys Material Designer by varying the volume fraction of carbon fiber. Now I would to have a look at stress distribution in the RVE for each design point. How can...
23 November 2023 6,063 3 View
RFID TECHNOLOGY PPT
11 October 2023 6,641 2 View
I would like to develop 2D open cell foam models which can be further used in the FE modelling. Could anyone please suggest any modelling tool? Thank you
05 September 2023 2,535 3 View
Dear RG community. I am trying to set up a fluorescent microscopic system for micro-PIV flow measurements. I am using a blue laser (473 nm) of 3mm diameter and I am expanding it using a 10X...
13 July 2023 1,973 3 View
I tried to troubleshoot it but still no use can anyone help me with this issue, ketone double bonds are missing in ligand map
02 June 2023 831 0 View
I need to develop a single module which should consists of multiple bluetooth modules .
27 May 2023 8,425 0 View
How the xrd values effect the medium , bulk and nano powders in the zinc oxide .
28 April 2023 5,891 1 View
I am teaching faculty is there any way to get IEEE membership at free of cost let me know and let me know any other memberships which exists which we can get at free of cost
11 February 2023 6,594 0 View
I am puzzled about the properties of gelatin, when used for tissue-embedding. Hard gelatin can be melt again by temperatures about 40°C. Formalin-fixed gelatin is like crosslinked protein and...
07 August 2024 1,686 1 View
I fabricated Ti3C2Tx using concentrated HF 40%, I plot an XRD as attached image below.. please let to know if I obtained it or not.
02 August 2024 6,789 4 View
Do these peaks in the curve indicate primer dimer or non-specific products?
01 August 2024 7,466 0 View
What is the best way to freeze the rat brain - liquid nitrogen, Dry ice , isopentane - after isolation for later protein investigation by Elisa?
01 August 2024 1,722 1 View
I need to Postfix mice brains. I slice the brains using microtome at 40 microns. These are Postnatal days 7, 11, 14, and 21. I am using half the brain for other analysis, so I need to fresh freeze...
31 July 2024 1,123 4 View
Generally, the target material is Mo, Co, Cu, Fe, Cr, etc, so on what basis should we choose this material?
31 July 2024 5,824 0 View
Dear Researchers, Is it feasible to distinguish between alpha and alpha prime martensite in the Ti6Al4V alloy under rapid solidification in the as-cast state using XRD, in addition to...
30 July 2024 3,849 0 View
Dear all: I am modifying Bismuth Tungstate with Hematite (Fe2O3), so I would like to know about how much Iron(+3) can form a solid solution in a Bismuth Oxide matrix. Best wishes Marco
29 July 2024 2,163 1 View
We assume that there is a physico-statistical meaning to the constant π other than circular geometry, but the iron guardians of the Schrödinger equation deny this. The iron guardians of the...
22 July 2024 4,285 9 View
could Nd (Neodimyum) doping into TiO2 because Nd's dense diameters are bigger than in TiO2
11 July 2024 2,350 2 View