Is it possible to view stress distribution in the RVE used to find the composite properties in Ansys Material Designer?

More Sadikbasha Shaik's questions See All

How to interface Semi conductor physics and Fluid flow physics in COMSOL?. What are the parameters to be considered while we interface them?

I am using a silicon nano wire in microfluidic channel to identify the some changes in parameters like voltage and current. but i am unable to interface them. the two physics run individually but...

10 January 2021 8,894 1 View

Is there any analytical model to asses impact of rigid projectile on monolithic deformable plate?

I am trying to select suitable element type (Solid or Shell) for impact analysis. I have tried with both solid and shell elements. The results are same for both element types up to certain impact...

08 January 2021 3,251 4 View

Why internal energy absorbed during impact is different when simulated with solid and shell elements using abaqus?

I am trying to simulate high velocity impact of rigid spherical projectile on a rectangular plate using Abaqus Dynamic Explicit. Particulars of Projectile Diameter : 12 mm Mass : 7.05g,...

04 January 2021 10,022 3 View

Can anyone suggest how to find proper OFDM MIMO Simulink model ?

I am doing my research on a communication system. I need a Simulink model with MIMO OFDM anyone of you could suggest me to find the total OFDM transmitter and OFDM receiver Simulink design model

21 December 2020 3,709 1 View

What are the challenges in Machine Learning to integrate it with Mobile Adhoc Network ?

What are the challenges in Machine Learning to integrate it with Mobile Adhoc Network

21 September 2020 3,881 5 View

How to calculate Poisson's ratio for sandwich panel?

I am simulating the compression test of the sandwich structure in Abaqus. How can I calculate? Please suggest me a method to overcome this problem. Thank you

05 July 2020 4,085 10 View

Which combining technique (MRC or SC) is better for Cooperative communication with Non-orthogonal multiple access technique?

I am using maximum ratio combing and selection combing techniques for C-NOMA. I want to compare the results for both techniques and also suggest me any other alternative combing techniques which...

27 January 2020 7,557 10 View

Network simulation for wireless sensor network?

I need to perform network simulation between wireless sensor network for my research work. Kindly suggest me which simulator is best and open source

21 January 2020 5,591 4 View

Which topic is best for research in machine learning?

i am new to machine learning,how to find out a problem for research,could you guide me plz. Thanking you.

25 September 2019 5,119 5 View

In search of IoT simulator that can be useful for simulating Lora network?

Dear Sir, i need an IoT simulator tool that can be supported for simulating LoRa network. To my knowledge, i know Simple IoT simulator but it is paid version. Thank you,

07 July 2019 7,561 3 View

flexibility of polymers chain

effect of double bond on the flexibility of polymers

07 April 2021 0 0 View

Formulation of polymer color flakes

I am writing to request some information for making polymer color flakes. I would appreciate the help.

17 March 2021 0 0 View

Polymer composites suddenly solidifies?

I am making polymer composite by solvent mixing method. When I am trying to add filler solution in polymer solution it quickly get solidified. How to make them then uinform? It doesn't give time...

03 March 2021 7,540 4 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

How to calculate BREQ 3 questionnaire?

how to calculate BEHAVIOURAL REGULATION IN EXERCISE QUESTIONNAIRE BREQ 3 ,which contain 24 questions and each question has 5 answers (0- Strongly disagree , 1-disagree, 2- Neither agree nor...

02 March 2021 811 3 View

I am interested in medicinal chemistry field, which books are highly recommended to learn from?

I am at the beginner level in drug design and drug discovery, and I am interested to learn more about this field. Which books are highly recommended to start from and gives me all essential...

02 March 2021 8,437 2 View

Please suggest a good text book for "Research Methodology in Life Sciences". Which book would be good for PhD Scholars?

Please provide Book Title and author name

02 March 2021 9,059 3 View