How to remove toluene from inorganic perovskite mixture?

25 May 2022 1 10K Report

I have tried to remove toluene from the mixture by Evaporation at 120 degrees but , im unable to remove toluene because it getting evaporated with the Perovskite .

Badges
Science topic

More Mohammed Shafik's questions See All

What are the values needed for gabor filter's parameter for cifar10 data?

Hi, I implemented a code to gabor filter cifar10 data but the images after being filtered and stacked are not clear like the original images. I think the problem is in the way I am using the...

03 March 2021 6,317 1 View

Is the a way to contol flow (Flow velocity) without impacting pressure value?

I have a pipe with 10 mm in Diameter and 2 bar pressure, the fluid velocity is 200 m/s, the fluid is air. is there a way to reduce velocity without affecting the pressure value?

25 February 2021 7,187 3 View

Can anyone suggest a topic for the Impact of AI and ML in the financial institutions?

I am currently doing my Master Thesis in FinTech and I am thinking of doing my project on the impact of AI and ML on the financial industry but as the impact of these technologies on the industry...

21 February 2021 7,128 3 View

Where I can find materials to learn Fuzzy VIKOR methodology?

Please suggest ways to learn Fuzzy VIKOR methodology in a best possible way. And is there any toolkit available for the same? Thank you in advance.

20 February 2021 8,271 3 View

What cause the beating of this signal?

I am trying to simulate the impact of a sinusoidal force on a Beam, yet I registred this beating signal (Displacement by time). The freaquency of excitation was the same as the first natural...

19 February 2021 5,872 3 View

How to apply a voltage sinusoidal/harmonic load in ANSYS APDL?

Hello all, I want to simulate a Dielectric Elastomer Actuator DAE (an electrostatic-Structural analysis). I want to apply various voltages and frequencies into the DEA in the form of sine wave....

13 February 2021 3,261 3 View

How to calculate time needed to evacuate a pressure from a tank using a pump?

Dear I have an air reservoir with 50 bar pressure , this reservoir is fed by 2 bar air pressure source, I would like to instal air pump ( 30 m3/h ) to evacuate the 2 bar fed pressure so I always...

06 February 2021 3,520 3 View

Observation instrument for classroom activity in consecutive interpreting?

Hello everybody My research involves an intervention where an instructor delivers a training course to students. My role as a researcher is to write down observations. Do you have any idea about...

03 February 2021 6,853 3 View

Inquiry regarding engineering journals for free publications for my dissertation (laser polishing of 3D printed parts?

my dissertation was on laser polishing of 3D printed plastic parts, i want to publish it, can anyone suggest me a free copy engineer journal for this purpos, plz?

01 February 2021 7,140 4 View

Is diversity in teaching methods for students important in communicating information?

26 January 2021 3,387 7 View

How Relativistic effects is one reason for lanthanide contraction?

The Lanthanide contraction which is the decrease in ionic radii of the elements in the lanthanide series from atomic number 57, lanthanum, to 71, lutetium, is due to poor shielding of the 4f...

01 March 2021 2,272 4 View

How to remove fatty material from plant extract?

The resultant solid was partitioned three times with 250 ml of petroleum ether (40-60/c) to remove any fatty material and evaporated to dryness.

28 February 2021 9,464 2 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How to improve the adhesion between germanium and silicon monoxide thin film layers using EBEAM evaporation?

I want to deposit multilayer coating of germanium and silicon monoxide on silicon wafer using ebeam evaporation?

21 February 2021 2,141 3 View

Mixture neutralization after Boc deprotection ?

I am performing a Boc-deprotection with HCl in organic solvent (dioxane or Ethylacetate) but would like to isolate the free amine. Several problems: - Neutralizing with inorganic base as NEt3...

18 February 2021 3,366 3 View

What is role of toluene and stearic acid in ball milling for powder ? In what weight percent we should add this to powder?

I am doing ball milling operation of Aluminum and silicon carbide powder. I am pretty confused about what should be added as process control agent ? what is role of toluene as PCA and stearic...

12 February 2021 5,205 3 View

Ligands with 3,4,5-trihydroxyphenyl group?

Hi In the design of a bidentate ligand with imine group, is it okay to have a 3,4,5-trihydroxyphenyl group in the structure? In other words, does the 3,4,5-trihydroxyphenyl group compete with...

08 February 2021 4,977 7 View

A film coverage that allows for transmittance of wavelengths on the infrared scale?

I've landed on needing some type of highly optically transparent film or cover material that prevents evaporation of culture media; I am not sure which subfield of materials science would be able...

08 February 2021 5,760 1 View

Are there any thermochromic materials that reflect infrared light (~9000nm) at 10C and transmit infrared light at 25C?

So I know some metal-insulators (ex VO2) have thermochromic infrared-reflective properties, but most of these are insulators at low temperatures and conductive at high temperatures. Some...

07 February 2021 1,770 3 View

What is the reason for using Glass Impingers?

Impinger bottles are used at some applications, where the gas is cooled and the condensate is dissolved in a solvent contained in the impingers. I have always seen impingers made of glass. Why not...

03 February 2021 6,959 2 View