Hi guys!
I'm modeling with abaqus. The model includes four faults. I want to know how should I prevent fault sliding in the geostatic step?
Is it OK to use tie constraint or it's better to use boundary conditions?
Thanks!
Tie may introduce a unacceptable displacement in geostatic step. You can apply boundary condition and later you can deactivate it in next stage.
Hello everyone What is your opinion about the introduction of an expert decision support system in which the rules are extracted from existing data without human intervention, instead of being...
31 July 2024 5,785 4 View
Hi, everyone This figure depicts a simulation of an electrostatic energy harvesting system in COMSOL Multiphysics software. My question is regarding the relationship between the changes in...
19 July 2024 4,694 4 View
For which types of polymers, the crystallization peak in heating cycle of DSC test can be observed and for which types cant? In another word, when this exothermic crystallization can be observed...
18 July 2024 348 3 View
Is it necessary that all element's pattern of an adaptive array antenna (null-steering) have exact similar pattern? If it is, What is the consequence of different element pattern in an adaptive array?
08 June 2024 5,201 2 View
Artificial intelligence (AI) has the potential to revolutionize education by providing personalized learning experiences tailored to individual students' needs. AI-driven systems can analyze...
21 May 2024 2,058 3 View
I am designing a software system for ordering satellite imagery in a way that by entering the specifications of the satellite orbit and its optical sensor, as well as the target ground area, it...
21 May 2024 6,519 1 View
I am wondering how to set up Cardiac fibrosis in vitro. I will appreciate all your comments.
15 April 2024 2,524 1 View
Dear Authors and Researchers, I'm looking for predictive technology models (PTM) for FinFET including 10nm. Unfortunately, the following webpages do not work...
14 April 2024 4,390 1 View
Hi In this simulation, i noticed that i have a electrical field inside a conductor almost in range of e-11. this upper plate is connected to 10volt (DC) and by time dependent study it moves...
13 March 2024 1,669 1 View
When financing projects, credit risk assessment is one of the most important components of a project risk management system and, therefore, requires special attention.The existing models used by...
11 March 2024 549 0 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...
08 August 2024 4,831 4 View
What should be the equation for halfway bounce back boundary condition for flow field with forcing term?
08 August 2024 7,938 1 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View