Is it possible to report hydrodynamic loads on different parts of an ocean vehicle while 6DOF motion analysis in Ansys Fluent is running?

It seems a 6dof UDF containing vehicle characteristics such as mass and moments of inertia can be used for specifying a boundary as reprentative of ocean vehicle. It is required to have...

03 February 2021 7,726 3 View

Is it possible to export mesh from abaqus for using in Ansys Fluent?

Hi everyone, I want to mesh a part in Abaqus for further use in ANSYS Fluent because this way, it is much easier and faster to get a high-quality mesh. Is it even possible to generate a file...

15 January 2021 5,665 3 View

What are the (extrinsic) factors that influence the citation rate of a research article?

Dear RG members, Excluding the (intrinsic) factors such as quality and content of an article, what are the extrinsic factors/predicors that influence the citation rate of a research article? Is...

07 January 2021 3,410 3 View

Natural frequency extraction with ABAQUS?

I have modeled the RC beam with simply supported BC and I have got the frequency value for the case of the beam, but I have 150 modes for each analysis and I have to see them one by one to find...

05 January 2021 8,626 3 View

How high is the saturation electric field of P-E loop in Relaxor Ferroelectrics?

I have prepared a relaxor ferroelectric (KNN - BZZ solid solution) bulk sample. During P - E loop measurements, we experienced saturation electric field of about 100 kV/cm before dielectric break....

29 December 2020 9,080 3 View

What is the best way to simulate the fractional controllers?

What software do you prefer?

29 December 2020 889 3 View

What is New Next Generation Attenuation Relationships (NNGAR) and how are they different from other attenuation relationships?

Dear researchers The provisions of ASCE 7-10 states that New Next Generation Attenuation Relationships (NNGAR) has been used in the process of Probabilistic Seismic Hazard Analysis (PSHA) to...

15 November 2020 1,132 4 View

Stiffness changes of the structures due to modeling P-Delta effects in Sap2000 are more significant than OpenSees. which is more accurate?

Dear researchers The modeling of P-Delta for the structural elements (specially columns) reduce the stiffness of the structure and consequently increase the period of vibration. Now, these...

24 October 2020 7,255 5 View

Why 256x256 medical image gives me 256x256x3 in matlab?

I need a 256x256 pixel image to use it in my project. I downloaded images from the internet, but when I read the image, it stored in a 256x256x3 variable (color image format PET images). the NSCT...

11 October 2020 686 13 View

What are your suggested topics for future research?

Hello to all professors and researchers, What is your suggested topic for conducting an academic-operational thesis in one of the most up-to-date and efficient fields? Please express your proposal...

07 October 2020 395 56 View

How to simulate Hetrojunction(SiGe Channel) finfet using matlab is it possible?

How to simulate Hetrojunction(SiGe Channel) finfet using matlab is it possible?

17 November 2020 193 3 View

How to add Stanford University CNTFET Model in OrCAD PSpice?

The HSPICE and Verilog versions are available here https://nano.stanford.edu/stanford-cnfet-model. Is it possible to add CNTFET model in OrCAD Pspice and if yes, what are the steps regarding this.

12 October 2020 916 2 View

How can i simulate dual-X second generation current conveyor using CMOS?

24 August 2020 8,067 4 View

How can I increase MAX_HEADER_BLOCKS value in Hspice?

I have designed a 16-Bit multiplier in Hspice and I got .tr file after simulation. While I try to load it in Matlab and extract circuit's information I receive below error in Matlab: "error in...

23 August 2020 7,974 2 View

Which signal (Pulse or DC) is often used for read and write operation in a SRAM memory cell.?

For the read operation, the WL will be at logic high (Vdd or let 1V) and initial condition at internal nodes (let Q and QB) are 0 and 1 V. The BL and BLB are also precharged to logic high....

14 July 2020 9,538 8 View

How to link MATLAB and HSPICE?

Hi every one, I have written a code for a simple digital circuit in HSPICE (Like a NAND gate). The width of PMOS and NMOS transistors is Wp, Wn, respectively. Now, I want to do the following...

05 February 2020 3,693 8 View

Gate All Around vs Continuous FinFET Thermals?

Can anyone help me know/compare the thermal challenges and limitations that gate all around have over normal continuous Fin devices. I understand that current density are bound to increase but...

20 December 2019 9,687 5 View

Can I design and characterise an image processor using FinFETs Technology in Cadence Virtuoso?

As a part of Master degree project, I want to characterise an image processor, specifically an impulse noise filter, by designing the whole layout in Cadence Virtuoso and analyse its temperature...

09 October 2019 4,547 3 View

How to measure power consumption of circuits with different typologies using HSPICE?

Hello every one. I want to measure power consumption of different circuits using HSPICE. Please look at the two different circuits in the attached picture. For Fig.1, I use the following commands...

09 October 2019 8,304 5 View

Book/ Article for learning basic circuit design methodology using CNFET?

I would like to learn the introductory and basic principles and design methodology using CNFET. Can anyone please provide me with the necessary books/ articles for circuit design using CNFET?

05 June 2019 3,994 10 View