Solar energy production forecasting ?

Hello everyone! I am interested in the topic of solar energy production forecasting for a ground-mounted PV system of more than 100MW capacity. Can anyone please suggest what are the main data...

08 February 2021 6,834 5 View

Why AC cables are always covered with the sand first and then covered with soil in solar park ?

I was curious to know why we only use sand for covering the AC cables inside the trenches and instead of having good isolation why these cables are covered. Why is there a problem in the trenches...

13 January 2021 6,008 3 View

Error encountered in executing MCE ?

In Terrset, an error encountered in executing Spatial Decision Modeller (MCE). During execution or run the MCE a massage come on the screen that reflects "Your columns and rows are not same" , I...

07 December 2020 1,542 1 View

How to do extract Urban Heat Island separately from LANDSAT image for each land classes?

I have already been read many articles and found some methods but those are not cleared to me. Can you please suggest me how to generate different LST map of each land classes using ArcGIS? Or...

25 October 2020 5,978 5 View

Can someone advise me to do Rietveld Refinement of the material whose Crystallographic Information Framework (CIF) file is not available?

10 October 2020 7,411 9 View

Recombination in Light emitting diode?

Why does recombination release light? It's one thing to say, 'and when the electron drops down it releases light', but it would be another level to explain how an electron dropping down creates...

28 July 2020 2,360 4 View

Has this COVID19 pandemic affected the renewable energy sector ? If yes can we analyse this affects with the help of data science and how ?

As the pandemic has affected each and every sector of the market, so my question is how big it has affected the renewable energy sector. If it has affected then can we have the specific results...

25 May 2020 6,643 7 View

No title

1. Why both models ("cv_mars" and "mars1") produced the same results? What is missing here? Even used another hyper_grid as Please click here https://stackoverflow.com/q/61216514/12675265

27 April 2020 3,876 1 View

How to conduct Monte Carlo uncertainty analysis for actual and predicted data in R ??????

I would like to conduct Monte Carlo uncertainty analysis for actual and predicted data in R; Kindly share some effective resources; However, I have this where understanding the hyperparameters...

08 April 2020 458 2 View

Which model can be used for a mix of I(1) and I(2)?

Dear members, I have a set of five time series. Two of them including dependent variable are I(2) and rest are I(1). Suggest me which time series modelling can be applied in this case? Thank you...

25 January 2020 2,780 3 View

Looking for Materials with high thermal expansion coefficient and high temperature resistance?

03 March 2021 8,272 1 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What are anisotropic electrical and optical properties of a semiconductor due to?

In some materials, properties such as band gap, thermal conductivity differ along different crystallographic axes. What are the basics?

01 March 2021 1,923 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View