How to overcome if elements exceed Jacobian error limit in ANSYS workbench static structural

More Bharath Kodangal Bhat's questions See All

For Rt PCR?

Is it necessary to run the Rt PCR product on agarose gel after completion?

29 December 2020 4,823 3 View

How to interpret MSWEP 3-hourly rainfall data 0.1 degree resolution?

I have downloaded the MSWEP sub-daily rainfall data (3-hourly data 0.1 degree resolution). I used MATLAB to convert it and obtained a table of dimensions 1800 x 3600 for a specific date. I am...

18 October 2020 4,205 4 View

Fan boundary condition using Ansys Fluent?

I am trying to model a jet fan being installed in a room. I want to study the flow of the fan coming out of the outlet (basically the development of streamlines). The walls of the room are...

12 October 2020 4,970 3 View

In Abaqus- How to optimize the shape of a particular region while keeping displacement at two points equal?

I am new to abaqus and I am trying to optimize a shape of a segment of a model (As a part of my master thesis). Please refer to the example model I have attached. I need to optimize the segment...

23 August 2020 5,828 9 View

Shall I submit the article simultaneously to another journal even after request to first journal to withdraw the manuscript???

I have submitted one of my review article on COVID 19 and ophthalmology in April through online submission but journal haven't overlooked it inspite of several request. Even i have sent request...

06 August 2020 1,802 3 View

When do I start applying for PostDoc position?

I just have completed my 4th year in PhD. I have recently got acceptance from a prestigious fluid mechanics journal "Journal of Fluid mechanics. My second journal for submission is underway. I...

05 July 2020 7,412 4 View

How do you transfer files from Open Foam to Star CCM ?

Hi I am trying to find some information as how to link up OpenFoam and Star CCM, however I am not able to find adequate information. Below is the details of the project. 1- Objective: to...

05 June 2020 8,484 3 View

How to start jupyter notebook from a particular folder instead of default root folder?

I am using python 3.6.8 on a Windows 10 machine. We can only move to subdirectories from the default installation (root) folder in jupyter. I wanted to start the notebook from a particular...

08 March 2020 9,259 4 View

Could anyone provide information about the significance of calibration frequency and its value for CMG3T-120 seismometer with Reftek-130 as Digitizer?

Actually I want to calculate instrument response constant for correction of instrument response of CMG3T-120 seismometer.The formula to calculate that can be given as...

06 March 2020 6,384 1 View

Determination of wavelength in Raw effluent?

Is there a procedure to determine the wavelength of an industrial untreated raw effluent using spectrophotmeter

24 February 2020 1,931 3 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Complex wave form in ANSYS?

Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...

27 February 2021 5,969 1 View

What is the best way to calculate the angles of twist for concrete columns subjected to torsional moment using finite element software?

In Finite element software like ANSYS , there is difficulty in obtaining direct results of twisting of concrete members because SOLID65 which is the unique element designed to represent concrete...

26 February 2021 3,806 2 View