Dear all:
I recently applied eigenvalue buckling analysis and edited the input file to get a Node file, and it successfully generated the file, but I cannot find a proper way to open it, could anyone help me?
Thanks very much!
Best Regards,
Mengli
Specify the options:
*FILE FORMAT, ASCII
*NODE FILE
....
in the input file and run your model in Abaqus. Then you can extract your results by using the appropriate functions of Abaqus2Matlab toolbox:
https://www.researchgate.net/publication/290440223_Abaqus2Matlab_-_Program_for_the_extraction_of_Abaqus_analysis_results_to_Matlab
Thank you very much Mr. George & Mr. Ali !
I will try the Matlab program
Hi dear Scholars: What ABAQUS does when embed 3D beam element not truss element to 3D solid elements? For my research, I need to use beam elements to bear bending moment when embedded to 3d...
31 December 2017 3,477 1 View
Hi Friends here: I am using Riks to modelling stability of a concrete prism, and need load in displacement control at certain eccentricity, I did well in concentric loading with a rigid body and...
10 November 2017 5,197 5 View
Hi all friends: I am modelling a round bar under axial compression, and want to impose pressure to the body through out the lateral surface, and I want the magnitude of the pressure varies along...
31 December 2015 4,175 5 View
Dear all mates here: I am struggling about a question when I apply pin boundary condition to a solid element steel bar in ABAQUS. I knew from another mate that as long as I restrain all the nodes...
31 December 2015 3,404 5 View
Dear friends here: Thanks for your reply to my previous questions, and I learnt really a lot from this forum, thanks everyone who helped me, May all the things goes well on you! Now, I found a...
31 December 2015 8,263 12 View
Dear all: I recently apply eigenvalue buckling to investigate the behaviour of a bar under compression, but when I set the boundary condition, there is another unusual option for me, and I cannot...
31 December 2015 8,955 4 View
Dear all mates: I recently had a talk to someone, and was told a very surprise opinion that If for a bar, theoretically we want to apply compressive pressure to both ends as axial compressive...
31 December 2015 3,225 3 View
Dear all: I apply ABAQUS to model a steel bar under compressive load, and use displacement control, but the result showed that at the beginning it was compressed, but later on, it was stretched...
31 December 2015 4,938 7 View
Hi all friends here: I am a new researcher and employ ABAQUS to analyse steel bar buckling through Riks algorithm, and concerning the stopping criteria, I want to ask a question. Since when we...
11 December 2015 3,407 3 View
Hi all: I got a tough problem about ABAQUS Riks, in the stopping criteria, I was asked to define the Maximum load proportionality factor. I know that the load proportionality factor was used to...
11 December 2015 3,135 8 View
I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.
11 August 2024 9,101 4 View
I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?
11 August 2024 5,138 1 View
Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!
11 August 2024 3,770 4 View
Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...
10 August 2024 7,180 0 View
I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...
10 August 2024 7,429 2 View
How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?
09 August 2024 7,718 0 View
I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...
08 August 2024 4,831 4 View
Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...
07 August 2024 1,937 1 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
A fungal strain was treated with nanoparticles. We want to do an environmental SEM analysis. So could anyone share your views on preparing the sample? Thank you.
07 August 2024 5,307 1 View