How to model the following in abaqus?

05 May 2015 0 9K Report

I am doing a parametric study on buckling on beams as shown in the attachment. I should use shell elements to model the I sections.

I have to take initial sway of the beam and residual stresses (during manufacturing) into account.

Badges
Science topic

More Vanadium Bismuth's questions See All

What kind of connections (Gas - leak proof) are suitable for quartz - steel at very high temperatures (800 degree Celsius)?

https://www.youtube.com/watch?v=NsGE9qeydlw It is a microwave fluidized bed. I think the transparent part of it quartz but how is the quartz connected to the steel jacket? What kind of...

31 December 2017 5,610 3 View

How do to convert Tyre pyrolysis oil to Diesel ( To be used as fuel for emergency backup power generator). What would be percentage of conversion?

What process should be done to the pyrolysis oil to obtain diesel which can run power back up generators. Should vacuum distillation with catalyst be used? Or Are there any other process to do...

10 November 2017 9,358 0 View

Do you have suggestions of potential improvements for material optimization in India?

What are the practices in construction in other countries which is different from India? Does codes in other countries facilitate the use of innovative materials. If so, what are they? Concrete...

06 July 2015 361 0 View

What are the types of buildings in India?

Can you classify them according to regional availability of materials in India? How do buildings differ from urban and rural areas? What are the most common types of building materials used? What...

06 July 2015 4,397 0 View

Concrete and Masonry are the most used materials. How can the usage of these materials be optimized?

Concrete and Masonry are the most used materials. How can the usage of these materials be optimized? Do you have suggestions of potential improvements for material optimization for construction...

06 July 2015 3,262 0 View

How to apply residual stress for rolled steel I sections in abaqus?

I am using the predefined field option in abaqus and I am going to use a empty static load step to allow it to reach equilibrium. Should I apply boundary conditions , Which boundary conditions...

05 June 2015 4,678 1 View

Is it easy to perform GMNIA in ANSYS for analysis of buckling of beams?

I would have to take residual stress in steel beams, initial imperfections and material non linearity into account. (GMNIA) . I would like to decide between RFEM and ANSYS. I need to perform a...

04 May 2015 6,290 1 View

In abaqus, Can I model an I section using profile option and yet use shell elements to model it?

I want to generate I beam sections but I want to model it using shell elements.

04 May 2015 7,232 1 View

How do I model fork support in ansys and rfem ?

From my understanding, Torsion and out of plane rotation should be restrained at both the supports. All displacement should be restrained at one support and In the other support, All displacement...

04 May 2015 9,896 3 View

Do you think it is warping free?

Does the boundary condition in Lt beam and abaqus match. I feel the model in abaqus is unconstrained. How to model the boundary conditions.

04 May 2015 850 1 View

How to learn more about SPSS and its Application?

I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.

11 August 2024 9,101 4 View

Can I base on reverse DNA sequences to perform alignment, convert to amino acids and GenBank submission?

I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?

11 August 2024 5,138 1 View

Baseline drift in HPLC? What causes this?

Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!

11 August 2024 3,770 4 View

Text-Communication from the M1 Hand Area using BCI—and then there is Elon Musk?

Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...

10 August 2024 7,180 0 View

Has anyone applied Python in the field of textile engineering for data analysis, automation, or smart textiles?

I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...

10 August 2024 7,429 2 View

How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?

09 August 2024 7,718 0 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

How to prepare the nanoparticle treated fungal sample for Environmental SEM analysis?

A fungal strain was treated with nanoparticles. We want to do an environmental SEM analysis. So could anyone share your views on preparing the sample? Thank you.

07 August 2024 5,307 1 View