How to model RC beam in ABAQUS?

10 October 2014 1 9K Report

I am trying with homogenous 3d solid element of concrete and wire element of truss type for steel..if any one has a video of the same.please post it and help me..as i am a beginner

Unnikrishnan B M

Roberto Nascimbene

I also think this is a very well written paper on this application

http://www.ipublishing.co.in/ijcserarticles/twelve/articles/volfour/EIJCSE4023.pdf

Badges
Science topic

More Unnikrishnan Bm's questions See All

How can I connect a steel plate (used to transfer the bearing stress, no contribution to strength) to concrete in abaqus?

1.A steel plate is used to distribute the load evenly to concrete, how to connect the plate(shell) to concrete(solid ) 2. I have to connect two parts (both solid and same material)which should...

06 July 2015 6,800 3 View

Can XFEM analysis be done after the first crack originate in ABAQUS?

Is it possible for XFEM to take off from the instant the first crack is originated? My aim is not to define the initial crack, i want XFEM to take off from a point once the crack initiation...

04 May 2015 7,018 2 View

How can shear crack be obtained in Abaqus?

for a RC beam with CDP material model is it possible to have shear failure by doing away with the shear reinforcement, it didn't work out for me. OR we have to change the material model for shear?

02 March 2015 6,750 3 View

Can you help me with damage parameters in concrete damage plasticity model in Abaqus?

The tensile damage parameter, dt is defined as the ratio of the cracking strain to the total strain. Similarly, the compressive damage parameter, dc is defined as the ratio between the inelastic...

02 March 2015 2,878 7 View

Getting the strain output in ABAQUS?

In a RC beam with CDP model i included field output request as E for total strain, however while getting the output i'am getting the LE output only which is the "logarithmic strain".Is it because...

02 March 2015 8,864 5 View

Anyone familiar with XFEM/ scripting in ABAQUS?

I have a RC beam with Concrete Damage Plasticity Model . I want to implement XFEM taking the first crack of my RC beam as the initial crack of XFEM, or in other words I want XFEM to start in the...

02 March 2015 2,418 4 View

In displacement controlled loading in abaqus?

I' am designing a beam with concentrated load Displacement bc should be applied on the reference point/ the point where load is applied? output request should be for reference point set or point...

01 February 2015 2,389 5 View

Can you answer my questions on tension damage and compression damage in abaqus?

I have designed an RC beam using CDP (Concrete Damage Plasticity) for concrete and elastic properties for steel, as per attached paper. 1. I am getting the tension damage at the bottom of the beam...

01 February 2015 3,401 4 View

Why do I get this srror while using concrete damage plasticity model in Abaqus?

Have you come across this error-"DURING THE CONVERSION FROM CRUSHING TO PLASTIC STRAIN Abaqus FOUND NEGATIVE AND/OR DECREASING VALUES OF PLASTIC STRAIN. VERIFY THAT THE DEGRADATION DATA UNDER...

01 February 2015 3,439 9 View

When i am giving displacement in abaqus?

In a simply supported RC beam when i give displacement at a node in abaqus, in order to draw the load displacement curve, i should plot U2 vs CF2 OR U2 vs RF2. I'am asking this because i'am...

01 February 2015 9,695 2 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Do you know best conditions for formation of best REE deposits?

I want to know more about REE deposits.

03 August 2024 6,930 2 View

What are the limitations and challenges of using machine learning for predicting concrete compressive strength in practical applications?

Machine learning (ML) has shown great potential in predicting the compressive strength of concrete, an important property for structural engineering. However, its practical application comes with...

03 August 2024 2,546 2 View

What is the best conditions for formation of REE ore deposits?

I want to know more about REE deposits.

31 July 2024 7,366 1 View

Simulation of metal drawing by Abaqus with UMAT?

Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...

30 July 2024 7,062 1 View

Why running a restart analysis in Abaqus in Ubuntu OS gives an error as attached when running the same job in Windows doesn't give any error and runs?

I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...

29 July 2024 9,572 3 View

How Can I Apply Hashin Damage Properties to Solid Elements in Abaqus Without Using VUMAT?

Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...

28 July 2024 8,169 0 View

Abaqus cylinder buckling riks analysis?

hi, I am doing a risk analysis of a cylindrical fuselage with windows. I have applied contact interactions between the different parts, and I have applied a unit value load to a reference point,...

20 July 2024 647 2 View