How to model EDL in channels by fluent?

Mushtaq I. Hasan @Mushtaq_Hasan

01 January 2018 0 3K Report

I want to study the electokinatic flow in microchannel and the effect of EDL by fluent.

Is there some one used the electropotenital in fluent and how it used?

Thank you

Badges
Science topic

More Mushtaq I. Hasan's questions See All

Please any one can help with modeling of elctro potentioal flow by Ansys Fluent?

If there is any one worked with electropotential model within fluent please advice how can activated and use this model to calculate the effects of EDL Thanks

01 February 2018 8,811 0 View

In scientific research. Which is make more contribution, the experimental work or numerical simulation?

to clarify the relative importance between two research approaches.

04 May 2017 4,723 2 View

Is it important to perform experimental investigation in very known field of research? or the numerical investigation is sufficient in this case?

to define the relative importance between the numerical and experimental approaches in scientific research.

04 May 2017 6,136 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Does anyone know HRM channel in a 2 plex QIAGEN Rotor- Gene Q qPCR can be used as a separate channel?

I am going to have 3 different probes in my qPCR work that I am going to do. But I realized that the machine we have in the lab is a Rotor-Gene Q 2plex HRM Platform, saying it has green, yellow,...

01 March 2021 8,544 1 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How do you mesh a thin solid in Fluent?

Hello, I have used the shell function on SpaceClaim to create thin solids for the model I am studying. These are contained within an enclosure for my study. I chose this approach as it avoids the...

24 February 2021 8,856 3 View

How the Ground Plane implantation is performed without damaging (and w/o varying the undoped nature) the top Si (8-10 nm) in FDSOI technology ?

It is a general practice to introduce Ground Plane in FDSOI devices under the BoX. The Ground Planes are introduced by Ion Implantation through Top Si layer and Buried Oxide. I wanted to know that...

24 February 2021 5,974 4 View

How to extract the y+ value from fluent ?

I am doing a 3D steady simulation of a wind rotor using Ansys Fluent. In order to have a y+ of 1, I created 10 inflation layers using total layer thickness method, and I started a first...

23 February 2021 2,819 3 View

Help with assigning pressure boundary conditions in FLUENT on a large structure?

Hello, I created a very tall tower (>1000m) and applied pressure boundary conditions at the inlet (bottom) and outlet (top) that correspond to the pressure are their relative altitudes....

22 February 2021 9,972 4 View