How to model a sea surface or sea state conditions in ANSYS ??

10 February 2021 0 4K Report

I am looking for radar cross section analysis with sea state modelling?

Badges
Science topic

Similar topics
Engineering
Modeling

More Rahul Agrawal's questions See All

Which type of compound does lamda max of 218 indicate in a uv-vis spectrum of a partially purified compound through column and TLC?

A crude extract of fungal culture using EtOH was subjected to column and TLC and partially purified compound was obtained. UV vis spectrum of the compound/s has max absorbance at 218nm. The...

11 August 2024 9,801 2 View

Which test should be used to study association among demographic profile and awarness level?

i have to study the awareness and adoption level of cloud computing in a district of India. i also want to use association among demographic variables like gender, age, education, income etc and...

02 August 2024 2,420 3 View

Conjugation of PEG-Amine to an Amino Acid Using EDC?

I am attempting to conjugate PEG to an amino acid at the C-terminus, for the purposes of producing nanoparticles. I have been told that PEG modified with amine groups can be used for this purpose,...

31 July 2024 2,033 1 View

What are the roles of both Monetry and Fiscal Policy coordination in optimising the Macroeconomic outcomes in the economy ?

These days policy coordination is becoming necesssary on different front. In India also it is the same case. Monetary and Fiscal policy interface is important in order to address the...

30 July 2024 2,104 6 View

Does soybean seed coat or cotyledon contain chlorophyl or flavonoids? What types? determined by paper chromatography? other methods (high school lab)?

Am trying to develop a lesson/lab to determine and compare antioxidant properties of soybeans of various colors. Preference would be low tech and low cost. Any assistance is greatly appreciated.

25 July 2024 7,498 2 View

Does post-translational protein modification cause devisions on observed pI verses calculated pI?

In running two-dimensional gel electrophoresis on bacterial protein, some spots that appear to match a protein sequence have a significantly more acidic isoelectric point than the calculated pI....

24 July 2024 8,076 3 View

Can we fit a gaussian Fit on a LIBS Peak ?

Though much literature suggests fitting a Voigt profile on a LIBS peak, is it also possible to fit a Gaussian profile on the LIBS peak? I have 204 spectra files, and I am building a pipeline for...

23 July 2024 6,127 1 View

How I can add anew research in my account ?

Their is new research published in the biological control journal, and I am one of the authors. I want to add it to my account at researchgare. How can I do this?

21 July 2024 7,545 0 View

Can Document Analysis be used as the only method of research?

I have read that it is better to use other research methods alongside document analysis for triangulation, although it can also be used as a stand-alone method.

18 July 2024 4,218 0 View

How much sample we are required to do a pilot study for standardized an Achievement Test?

I am conducting a study on Effectiveness of e-content on academic achievement of secondary school science student.

17 July 2024 5,633 4 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

Why is there a significant edge deviation in radar point cloud and camera registration?

The above are manually labeled extrinsic matrices based on the first image It can be seen that the projection error at the edge is large, while the error at the center is small. What could be the...

23 July 2024 7,479 3 View

Why my simulation results are showing too much deformation compared to experimental result?

I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...

13 July 2024 3,631 4 View

Can I transfer the 3D file from Matlab to Ansys or Abaqus?

I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?

09 July 2024 9,226 3 View

How to solve the question of ansys fluent?

Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."

30 June 2024 7,894 1 View

How to import STL format into ANSYS APDL?

Hi everyone, I want to import an STL geometry (surface meshed with 2D meshes) into ANSYS APDL. After importing, I also want to mesh the structure with SOLID187 elements to convert it into a solid...

25 June 2024 4,286 4 View

What is the difference between the rotational velocity and cmrotate command in ansys?

I am trying the simulate the drum brake squeal in ansys. For giving the rotational velocity to drum what should i use the Rotational velocity or CMROTATE command.

24 June 2024 5,125 0 View

What is the difference of one-port and two-port data in the radar signal processing?

For the radar signal processing, we can use either one port signal (ex. S11) and two port signal (ex. S21). What is the difference or pros and cons of the two methods?

20 June 2024 6,052 1 View