The Akaike information criterion of the random forest model ?

Please, how to calculate the number of model parameters of the random forest model to determine the Akaike Information Criterion (AIC) using this following expression: AIC = n * log(MSE) + 2 *...

27 January 2021 816 6 View

Any propositions for scientific journals for AI (machine learning) that do not take time for reviewing, max 3 months for response?

im searching for journals that do not take time for reviewing and response for max of 3 months. Not open access journals.

27 December 2020 1,978 9 View

Is it better to normalize Nile red absorbance to Bradford assay or to cell number?

I stained the fat droplet inside the cell using Nile red and read the absorbance by a microplate reader. Which better to do, normalize the Nile red absorbance to Bradford assay or to cell...

12 December 2020 8,036 2 View

Calcul Max (Stress, Strain) In Excel?

Dear researchers, I performed mechanical tensile tests and obtained results in the form of two columns (force in N, displacement in mm) after I calculated (stress in MPa, strain %). I would like...

05 October 2020 3,024 2 View

What are the adverse effects of mercury on atmosphere ?

05 October 2020 3,241 13 View

What is the time required to complete the reaction of green synthesis of nanoparticles?

The time required to complete the reaction of green synthesis of nanoparticles.

01 September 2020 8,497 4 View

Are you interested in learning about post war reconstruction?

Third edition application is open soon... if you are an Engineer, medical doctor, teacher, manager ...etc. and interested in learning about reconstruction, and development management , this is...

06 August 2020 1,139 3 View

Which is the best framework to use for building deep learning models to process big data (hadoop cluster), tensorflow or h2o?

im searching for efficient frameworks and easy to use, that implement deep learning models on big data (hadoop cluster)

20 July 2020 7,667 3 View

If there any command in Matlab Simulink , can make the optimization run and finish fast as you can in GA ?

Dear and greeting all researchers, I'm interested in optimization with several kinds of algorithms as an example GA, PSO, DE, GW, and others, but in this question asking, I specified for GA only,...

11 June 2020 2,064 2 View

Acceptance and production (Taylor & Francis)?

How much time remains between acceptance and production (author agreement) of the article in the journal of natural fibers ( Taylor & Francis).

24 May 2020 1,908 2 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Complex wave form in ANSYS?

Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...

27 February 2021 5,969 1 View

What is the best way to calculate the angles of twist for concrete columns subjected to torsional moment using finite element software?

In Finite element software like ANSYS , there is difficulty in obtaining direct results of twisting of concrete members because SOLID65 which is the unique element designed to represent concrete...

26 February 2021 3,806 2 View