In PRIMER, is it possible to downweight certain taxa in multivariate community datasets to reflect uncertainty around identification??

I have a dataset with about 80 different species. As usual, some species are very easy to identify with certainty whereas others are more difficult, which means that I am less certain of my...

03 March 2021 8,066 4 View

How to get onecolumn document from standard IEEE ACCESS LateX template?

I have prepared a manuscript in IEEE Latex template, but for some purpose, I need to prepare a word file as well (detailed format is not required). Compared to two column .tex file, one column...

02 March 2021 1,830 3 View

Gel electrophoresis result for total RNA samples, 1.5 Agarose gel was used, How to improve the integrity of RNA?

Gel electrophoresis, RNA degradation, RNA extraction from fresh tissue

02 March 2021 5,433 5 View

How to grow E.coli on the low salt LB agar plate with 50 or 100ug/ml of Blasticidin?

Hello, I would like to ask how to grow E.coli which resists 50 or 100ug/ml of Blasticidin. I have tried many methods by using low salt Luria-Bertain(LB) agar plate. However, no colonies grow. Let...

01 March 2021 2,027 2 View

OpenBCI eeg--has anyone used them?

I'm looking to try out an off-the-shelf EEG set for some exploratory work. Curious if anyone has used the OpenBCI, and how much set-up work is required. I've heard they are more difficult to get...

01 March 2021 4,128 3 View

How to remove DCU and HOBT from my reaction?

I am doing a acid and a chiral amino alcohol reaction using DCC and HOBT in DCM or THF? Can anyone suggest me how to remove DCU and HOBT from a reaction mixture??

28 February 2021 2,153 1 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

B-mercaptoethanol (BME) protocol?

Hi everybody, I have been running a multiplex IHC which allow me to stain the same tissue with different markers (Primary Ab + Secondary conjugated Ab) (AF487, AF555, AF647). Since I would like to...

27 February 2021 5,028 2 View

Is IMPACT FACTOR justified in case of Taxonomy?

There is huge pressure of getting good impact factor on scholars now a days. On the other hand Taxonomy is a very dry subject and the concerned papers can only get citation in same group of organism.

26 February 2021 5,851 1 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Why does blocking with my immunogenic peptide cause nuclear fluorescence in ICC?

Hi all, I am validating a polyclonal antibody raised against human ANT4, through WB and ICC. In most of my controls, the antibody shows very little off-target binding, but when I pre-incubate the...

03 March 2021 5,999 3 View

Irradiation data for JAPAN?

Hi, Could you help me to get the latest (2019, 2020) solar resource data for a particular site in JAPAN? PV GIS and NSRDB data are not in reach to JAPAN, I'm looking for some other database for...

03 March 2021 961 3 View