09 May 2024 1 5K Report

Hi all!

I would like to know if there is a method to polymerize low MW cellulose triacetate (e.g. re-engaging in acetylation). Or this is not possible and the MW of my cellulose source should be high?

Thanks.

More Polo Jerome Daquipil's questions See All
Do head direction cells necessarily encode in an allocentric reference frame?

According to the vertebrate literature, I got the impression that head-direction cells are always anchored to an allocentric reference frame. This can easily be tested with freely moving animals....

27 January 2021 3,821 3 View

What is the best method to check interaction between a drug and a protein ?

Hi, I would like to know the best method to check the interaction between a proteine (cruzipain, cysteine protease) and a drug. It has been purposed to our project to evaluate protein-drug...

30 October 2020 7,209 3 View

Is It possible to design Affinity Chromatography Column with the Drug of your choice ?

Dear, I am interesting in Drug /cellular partner interaction analyzed by High Performance Affinity Chromatography (HPAC). I ask The question and I open a topic to know if It is possible to...

13 October 2020 7,504 3 View

How to select pixels by color in ImageJ?

I want to use ImageJ for counting my different tephra populations in a thin section sample, but I am not able to separate the lighter populations from the darker ones in ImageJ before counting. I...

28 September 2020 5,471 2 View

Is it possible to do Publication for my research paper ( 4 years back )?

Hello I would like to ask if it is possible to publish a paper in which I did my research, four years back but I didn't publish it. So if I want to publish it now is it possible? Thank you

05 April 2020 1,805 3 View

Cancer cells phagocytic assay - proper gating strategy ?

Good afternoon. I have some concerns regarding my gating strategy for a phagocytic assay. Here is the experimental setup : I incubated mouse bone marrow derived macrophages (BMDM) with B16F10-GFP...

18 March 2020 8,851 3 View

What journals focus on diagnostic laboratory medicine and global health/policy?

Hi folks, A niche question, but does anyone have a recommendation for scientific journals with a focus on the place laboratory medicine holds within crisis/disasters/global health apart from the...

08 March 2020 3,796 3 View

Which MCDA-method (and/or software) is most suitable for a decision with alot of scenarios?

For my thesis, which thematizes a GIS-based industrial site selction in Europe, i am in need of a method to integrate all of the european NUTS 2-regions (253 units). The methods which i had in...

29 February 2020 6,743 5 View

Test Methods for Compressive Strength of Circular Hollow Section?

I am searching for test methods and standards for compressive strength of circular hollow structural steel (hss). My research is about analysis of using CFRP to increase the compressive strength...

16 November 2019 7,047 3 View

Does anyone has any protocol to decrease cell membrane fluidity on extracellular vesicles (EVs)?

To determine the content of EVs and their possible biological impact on different cells can be challenging. Interestingly, we have found some EVs can induce differentiation on certain specific...

22 September 2019 9,776 1 View

Similar questions and discussions
MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

Protein-aptamer gel electrophoresis help, please??

Hi, I have problems with running gel electrophoresis. I have tried agarose gel electrophoresis and native PAGE. I have two proteins, which have molecular weights of ~30kDa and ~180kDa and two...

03 March 2021 4,275 4 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close