What kind of steel moulds are used for hot pressing metal powders?

My main concern is that the metal powders should not weld to the mold surface and I should easily be able to eject out the pressed samples. I am looking for alternative for graphite moulds. The...

22 February 2021 2,965 4 View

I am electroplating Ni on a stainless steel. At temperature and time should I anneal so that Ni thermally diffuses into stainless steel?

I am electroplating Ni on a stainless steel for abrasive application. At temperature and time can I anneal so that Ni thermally diffuses into stainless steel? My intention is to improve the...

20 October 2020 7,092 3 View

What are the hot topics in today's situation where an engineer should focus for betterment of society, e.g. Rural development, Solar farming, etc.?

We engineers sometime busy in doing research in countless unpractical, non urgent, not beneficial to society like areas for increasing count of our research articles. But we know an engineer is a...

17 July 2020 1,950 16 View

Relative telomere length calculation with Ct values?

10 May 2020 7,398 2 View

Can any one suggest me what are improvements i can do in clustering of wireless sensor network based on residual energies?

I have already implemented clustering algorithm for WSN(IoT) based on remaining energies of CH's. But i need to improve algorithm for my academic project. Please suggest me the possible...

01 April 2020 3,357 5 View

Could ecological risk indices applied for water samples?

Could Pollution indicators such as degree of contamination index (Cd) and potential ecological risk index (PERI) proposed by Hakanson (1980) also considered for water samples to represent surface...

24 March 2020 7,345 4 View

What should be the average size of amplicon if I am using LBb1.3 (left T-DNA border) and RP (gene specific Reverse primer) against genomic DNA ?

Hello everyone! I am thinking to amplify T-DNA insertion region using LBb1.3 (left T-DNA border) and RP (gene specific Reverse Primer) against the genomic DNA of one of the T-DNA insertion mutant...

11 March 2020 1,239 3 View

Error while compiling WRF - "compile [-j n] wrf compile wrf in run dir (NOTE: no real.exe, ndown.exe, or ideal.exe generated)" Need solution ?

or choose a test case (see README_test_cases for details) : compile [-j n] em_b_wave compile [-j n] em_convrad compile [-j n] em_esmf_exp compile [-j n] em_fire...

06 February 2020 810 8 View

Which software is mostly used in industry for static structural analysis?

Most used CAE software used in industry for static structural analysis.

25 January 2020 6,260 3 View

Kindly explain how to calculate interaction volume from incidence angle in XRD?

26 November 2019 4,411 3 View

What are the steps to use the Axoclamp-2A amplifier for Two-electrode voltage clamp (TEVC) mode?

I'm using Powerlab y Labchart 8. I would like to know about 1. Initial Amplifier Settings 2. BNC Connections to the amplifier 3. voltage clamp procedure

31 December 2018 6,154 2 View

What electrode should I use for point-stimulation of cardiac monolayers?

I am forming small cardiac monolayers on glass coverslips and would like to provide point stimulation using my laboratory's existing Powerlab system that is usually used for isolated hearts. We...

11 December 2018 1,852 0 View

How can we avoid interference while recording EMG and GSR at the same time?

We have observed a large noise increase in facial EMG recording when skin conductance electrodes (GSR) are applied. This seems to be caused by the fact that GSR amplifier produces currents that...

21 January 2015 4,114 3 View

How can we avoid interference while recording EMG and GSR at the same time?

We have observed a large noise increase in facial EMG recording when skin conductance electrodes (GSR) are applied. This seems to be caused by the fact that GSR amplifier produces currents that...

31 December 2014 473 3 View

What is a good device to measure blood pressure non invasively in isoflurane anesthetized C57Bl/6?

Hi everyone, I am doing in vivo imaging in the kidney of mice and I want to measure the blood pressure of the mice while I am imaging them. I want to control the anesthesia depth on one hand but...

29 September 2014 6,406 3 View

What is a good device to measure blood pressure non invasively in isoflurane anesthetized C57Bl/6?

Hi everyone, I am doing in vivo imaging in the kidney of mice and I want to measure the blood pressure of the mice while I am imaging them. I want to control the anesthesia depth on one hand but...

08 September 2014 1,428 4 View