How to incorporate the Groynes/ Spurs/Dikes in CCHE 2D hydrodynamic model?

10 February 2015 1 10K Report

Hello Sufia Zaman,

We can raise the initial bed level elevation along the mesh according to groyne height and length. Please do remember that we can raise elevation along the ith or jth line of mesh, so create the mesh accordingly with the position of groyne

Badges
Science topic

Similar topics
Physical Sciences
Waves

More Vinay Chembolu's questions See All

How to calculate chemical quantity required when relative molar composition is given ?

Relative molar composition of 1.0 TEOS : 0.2 CTACl : 0.0026–0.017 LS277 dye : 10.4 TEA : 142 H2O was used.

04 April 2024 6,770 1 View

Scoliosis Research Society srs22r questionaire in german ?

Looking for the srs22r questionnaire for evaluation of scoliosis patients. The study group in Tübingen (Germany) - have validated and published this. Can anyone kindly send me the srs22r score...

20 March 2024 8,696 0 View

GPPS/Glass fiber composite?

I am preparing general purpose polystyrene (GPPS) glass fiber composite. I want to know what coupling agent can be used and what glass fiber grade would be suitable for GPPS

17 March 2024 8,465 1 View

User Graph Traversal with weighted edges: Should we consider a multiplication of confidence scores in finding related nodes?

Hello! I have the following heterogenous graph - One of the vertices represent users and weighted edges between these user vertices represent the confidence we have in those users being the...

25 February 2024 9,930 0 View

Conductive Ink using CNT/ graphene/ nanoparticles?

Hii, Can anyone please suggest articles for preparation of conductive ink using CNTs/graphene/ nanoparticles, etc.?

22 February 2024 7,694 2 View

Is the drug adsorbed or absorbed in nanoparticle during or after loading the nanoparticle with the drug?

How does it depend on the nature or class of nanoparticles?

02 February 2024 4,015 2 View

How to define fiber orientation for a give composite part?

Greetings, Hello everyone, I designed a boat hull in Catia V5. I want to define ply sequence and direction for that structure. I did lots of research but I couldn't find the appropriate solution...

05 August 2023 5,864 2 View

Is azide group stable to TFA in SPPS?

I want to conduct click reaction with azide in Fmoc-SPPS.

02 August 2023 3,159 0 View

Does rinsing a cuvette during measurement by UV Spectrometry needed if working on quantification of a compound say phytic acid in a triplicate run?

or we can empty the cuvette with the previous sample and tap the cuvette on a paper towel and continue with replicate 2 and 3 and finally rinse when using sample 2. A curious question in case of...

09 April 2023 7,544 1 View

Can anyone suggest a topic for PhD related to Quant fund and Digital currency?

Quant fund and Digital currency

04 April 2023 2,779 1 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

Given the current level of natural phenomena cause by the climate change and environmental pollution, will the AI find the technological solutions?

AI-driven technologies offer previously unheard-of capabilities to process enormous volumes of data, extract insightful knowledge and improve predictive models, according to the UN’s World...

31 July 2024 9,733 3 View