How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View

What are the important tips for writing review articles?

Important tips for writing a good review articles

24 February 2021 8,544 6 View

How can I verify my centrifugal fan design for electric motor cooling?

I have radial blade centrifugal fan design which will be mounted on exhaust side of electric traction motor. The fan will be mounted on same motor shaft inside the housing. How can I verify that...

23 February 2021 2,390 3 View

What is the method of removing RNase contamination from a filter paper surface?

I am working on a biosensing project on paper substrate, however, it is found that the RNase contamination occurs on the filter paper. Might I ask is there any method to clean the paper surface...

12 February 2021 3,926 3 View

What is causing the raw fluorescence to be negative?

Hi everyone, I would really appreciate it if someone can tell me when and why a raw fluorescence starts below zero. In the picture attached below the blue colour curve starts from a negative...

09 February 2021 4,642 3 View

Regarding immunology, transmissivity, herd immunity and vaccines in Sars CoV-2?

This is a follow-up on an earlier question regarding mechanistics of vaccines: why current vaccines don't block transmission. In summary, they don't engage mucosal immune cells to produce IgA....

08 February 2021 8,321 3 View

How can I enter the load increment values to the Abaqus?

In Abaqus I know that there are two methods for incrementation (Automatic and fixed incrementation). I want to control the incrementation by myself. I want to input the values of load increment...

03 February 2021 6,943 3 View

Distortion problem in Abaqus explicit?

Dear all. I'm modeling the RC column with cyclic displacement by Abaqus-Explicit. The concrete model used Concrete Plastic Damage model. However I'm facing with a error about the excessive...

01 February 2021 7,726 1 View

I am finding a lot of cellular debris in the culture flask? What are the reason behind it?

I am facing a problem that cellular debris observed in my SHSY5Y cells. I have seeded the cells in DMEM media with 10% FBS in T-25/ 60mm dish (antibiotic used PEN-Strepand gentamycin). I have also...

17 January 2021 3,074 3 View

Does Lucifer Yellow interfere with miniEPSC/IPSC recordings?

I want to mark the neurons I am recording from during whole cell Patch clamp. I am thinking of using Lucifer Yellow. Does it increase noise during recording? What are the better alternatives to...

04 January 2021 7,791 3 View

Which fluorescent dye to use for measuring total ROS production?

Is DCFDA appropriate for measuring total ROS production, or can it only detect certain types of ROS? If I want to measure total ROS production, which dye should I use?

01 March 2021 9,447 3 View

Is there anyone who experienced with cytotoxic effect of Hoescht 33342 dye?

Is Hoechst toxic to cells? In general, it is known as non-toxic. I am working with dsRED MDA-MB-231 cell line. I applied it for my PDMS-based microfluidic platform, for this reason, I incubated...

26 February 2021 9,119 3 View

How to get/count refractive index in gasses?

20 February 2021 8,202 6 View

In methylene blue test Why is UV absorbance reading very low as soon adsorbent is added and then increasing before reaching equilibrium?

Hello, I'm working on removal of methylene blue. 01. in the dark test very first reading is taken 15 minutes after adding adsorbent to the dye solution and that UV absorbance reading is very...

19 February 2021 472 5 View

Has anyone performed a colorimetric RT-LAMP assay using Lucigens LavaLAMP kit?

Hi there, my lab recently opted to use LavaLAMP from Lucigen instead of the Warmstart kit from NEB. However, Lucigen has yet to create a colormetric kit for RT-LAMP, and adding phenol-Red (pH...

17 February 2021 5,399 1 View

Want to ask about equivalence ratio?

09 February 2021 5,273 2 View

Why stop the reaction in ice for the fluorescent probe FDA (fluorescein diacetate)?

Hi, In literature I noticed that who stains haemocytes with FDA for 30 min then stop the reaction in ice while this does not apply for 15 min incubation time (or maybe authors did not write this...

08 February 2021 3,366 3 View

What is the possible cause of MSCs low growing?

Hello Everyone, We are inexperienced in culture of MSCs trying to grow a sample from BM of a mare. It is the second time that after preparation of new medium (DMEM-F12 with high glucose - 10% Hy...

07 February 2021 9,989 7 View

Why do cells die after adding MTT dye?

I was doing MTT assay, and in the last day before adding the MTT; the cells looked good (or so I think), but after aspiration of the drug and addition of MTT dye I noticed that most cells seemed...

07 February 2021 3,846 4 View

How to measure the concentration of a labeled protein with no tryptophan or tyrosines?

Hey I'm trying to measure the concentration of a protein I've purified and then labeled with Atto 647 flourescent dye. The protein has no tryptophans or tyrosines (although does have...

04 February 2021 4,482 4 View