How to extract X,Y,Z components of a toolpath?

How to extract X,Y,Z components of a tool-path G-code by using MatLab or Excel? I am working on single point incremental forming and the sample tool-path is attached ;please check the video. i...

04 January 2018 1,111 3 View

What suggestion do you have for a CV curve becomes narrow at 50 mV/s and above scan rates than the CV curve obtained at 20mV/s?

When I measure the CV of the polypyrrole composite as working electrode using Ag/AgCl, Pt and 2M NaCl as reference electrode, counter electrode and electrolyte solution respectively at scan rates...

09 August 2016 6,394 2 View

I always get broad cv curve for low scan rate and norrow cv curve for high scan rate. what can be the reason for this type of inverse relation?

15 July 2016 4,552 10 View

How to do Matrix inversion using FPGA ?

I need to implement matrix inversion in hardware. The size of the matrix can be anywhere from 50 *50 to 8*8. Are ready-made standard codes available or inbuilt modules available with FPGA...

15 February 2021 4,006 3 View

Steps for Hardware Implementation of Max Log MAP Decoder simulated in MATLAB?

How to implement max Log MAP algorithm turbo decoder on FPGA? Simulation is done on MATLAB. What are the next steps to be followed? Do I need to use HDL Coder feature in MATLAB? Is it needed to...

07 January 2021 4,405 4 View

How can I verify the design on the FPGA ZedBoard?

I have designed AXI Interconnect to connect 4 masters and 1 slave using SystemVerilog and Vivado Tool. The simulation stage of the design is working well. In the design, there are more I/O pins...

06 January 2021 8,487 2 View

How to interact with internal memory of FPGA and connect it a signal or array inside a module?

I am trying to implement a processor tile on FPGA using vivado but it is taking too long to synthesize design due to large amount of Instruction and Data Memory. Currently, I have put complete...

05 January 2021 8,349 1 View

How can I roughly estimate the current denisty in an FPGA?

Hello, I am currently working on the estimation of the electromigration of an FPGA. We just performed the construction analysis so we know all the values of wire width and height for each metal...

22 June 2020 2,743 3 View

Why there is'nt a High level frame built on top of Hardware descriptive languages for rapid experimentation/prototyping? For e.g Keras in Python?

High-end APIs of python, Tensorflow and Keras dramatically reduce the time and effort put into experimenting and deploying DL/ML models for various tasks. but I can't seem to find a High- level...

11 May 2020 4,252 7 View

Does any FPGA contains DEMUX in side as basic building block as it has LUT?

I have written code for DEMUX and it is synthesizing it with LUTs only and it is not taking DEMUX into consideration while synthesis. why? I am using xillinx zybo board and synthesis with vivado...

10 April 2020 1,235 3 View

Is it possible to implement the real-time model predictive control on Raspberry Pi ? If not, than can I use an FPGA board with the Pi?

I am trying to implement a model predictive controller to control my soft robot. Right now, the robot is being controlled in an open loop. I have written python code for the MPC but the codes are...

05 March 2020 835 3 View

How to take Real time Sensor data on an FPGA?

I am working on processing real time sensor data on FPGA using Neural Networks. But I am not able to acquire the data on FPGA. One solution was suggested that I use High Level Synthesis(HLS) for...

26 February 2020 4,024 5 View

Are there any reliable open source alternatives for HDL Simulators ?

I am looking for an open source alternative for HDL Simulators such as Modelsim Student Edition (limited version). Any suggestions??

17 February 2020 2,948 3 View