How to implement a Autolab PGSTAT 302N with a lock-in amplifier?

15 April 2016 0 8K Report

I am doing chronoamperometry with an Autolab PGSTAT 302N and I want to implement it with a lock-in amplifier so that the current detection limit can be pushed to sub-nA. However, I noticed that I can't find the current output port from the PGSTAT 302N panel. The lock-in amplifier I'm using is SR810 from Standford Research Systems. Can anyone give me some suggestions? Thanks a lot! That is going to save me!!

Badges
Science topic

More Zhaoxia Qian's questions See All

How can I remove the problem occurs in ciorth in Molpro calculation?

Hi all, I am new to the computational suite"MolPro" and I am trying to do the Electronic energy calculation for a small system. Following is my Input...

29 March 2024 1,178 2 View

Do you know that there is the emission of ultra-high electrons with energy up to 790 TeV downstream of the RF cavity in the electronic storage ring?

Through my preliminary experiments, it was found that there is an emission of abnormal ultra-high energy electrons downstream of the RF cavity of the electron storage ring, which I theoretically...

12 March 2024 8,573 1 View

Temperature for PCR machine lid during ligation?

What should be the temperature for PCR machine lid during ligation overnight at 16c? Will the usual lid temperature at 105c affect the ligase performance?

20 February 2024 7,765 3 View

Why protein ladder starts separating in sds-page stacking gel?

I made two 10% sds-page gel (10% resolving and 4% stacking) and run them at 20mA. I am testing whether my newly edited recipe for gel casting is correct or not. Apparently, the gels took 3hr for...

13 December 2023 7,487 1 View

A line appeared on the SDS-PAGE gel, what is the cause?

I am optimising a new protocol for SDS-PAGE using 40% acrylamide 29:1 solution from Bio-Rad across different percentages. I casted two 6% equivalent gels according to the protocol I have...

08 November 2023 7,022 0 View

Eosinophil cell marker?

please recommend best markers for eosinophil. Thanks.

05 September 2023 7,938 0 View

SiC atomic bonding energy same?

Atoms of SiC material, one silicon atom will connect four carbon atoms, is the bonding energy between this silicon atom and four carbon atoms the same?

23 July 2023 9,880 5 View

Are immature RBCs and erythropoietic progenitors resistant to RBC lysis?

I am thinking of sorting Ter119+ cells from the spleen and bone marrow to look at the transcription profile in immature RBCs and erythropoietic progenitors. Could I use RBC lysis to remove mature...

06 July 2023 7,826 0 View

FDTD simulation of black phosphorus absorption?

I want to use FDTD to simulate black phosphorus absorption A. Since black phosphorus is not in the material library, I add 3D new material by looking for the permittivity. The references are...

01 June 2023 5,739 1 View

How to isolate the primary liver sinusoidal endothelial cells (LSEC) ?

I've used to isolate LSECs several times with percoll before, but all failed. I'm looking for someone here with relevant experience to give me some guidance. If I get useful suggestions, I'll...

03 May 2023 2,294 0 View

How to learn more about SPSS and its Application?

I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.

11 August 2024 9,101 4 View

Can I base on reverse DNA sequences to perform alignment, convert to amino acids and GenBank submission?

I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?

11 August 2024 5,138 1 View

Baseline drift in HPLC? What causes this?

Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!

11 August 2024 3,770 4 View

Text-Communication from the M1 Hand Area using BCI—and then there is Elon Musk?

Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...

10 August 2024 7,180 0 View

Has anyone applied Python in the field of textile engineering for data analysis, automation, or smart textiles?

I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...

10 August 2024 7,429 2 View

How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?

09 August 2024 7,718 0 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

How to prepare the nanoparticle treated fungal sample for Environmental SEM analysis?

A fungal strain was treated with nanoparticles. We want to do an environmental SEM analysis. So could anyone share your views on preparing the sample? Thank you.

07 August 2024 5,307 1 View

How to normalize and take the significance of the MTT OD values with 3 replicates for the same cell-line?

Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...

07 August 2024 8,106 4 View

What procedure should I follow for current controlled PPy film electrochemical deposition on ITO?

For example, I perform passivation process before electropolymerization of Py for adhesion to titanium surface. Is a similar or different procedure required for ITO? If necessary, I would be glad...

06 August 2024 3,176 0 View